Search Results "Ramp Width"
Filters
Commonly Searched Documents
-
Figure 406.6 Diagonal or Corner Type Curb Ramps – Drawing from the U.S. Access Board
-
M303.3.3 Ramped (Section-by-Section Analysis)
technical requirements for running slope, cross slope, clear width, edge protection, and handrails....
-
4.8.4* Landings
Ramps shall have level landings at bottom and top of each ramp and each ramp run. Landings shall have the following features:...
-
ElectionSource Voter Accessibility Expansion Door Hinge
Add 2'' of width to any doorway in your offices! Excellent for use on bathroom doors which are usually a tight fit for those in wheelchairs....
-
Features of Accessible Parking Spaces
If the accessible route is located in front of the parking space, install wheel stops to keep vehicles from reducing the clear width of the accessible route below 36 inches. 3....
-
404.2.3 Doorways - Clear Width
Door openings shall provide a clear width of 32 inches (815 mm) minimum....
-
11B-404.2.3 Clear width
Door openings shall provide a clear width of 32 inches (813 mm) minimum....
-
11B-404.2.3 Clear width
Door openings shall provide a clear width of 32 inches (813 mm) minimum....
-
Madden Manufacturing Round Handrail (ADA Compliant)
Contractor ADA Handrail is an innovator in mechanical ADA fittings and systems. Available in kit form or full length extrusions, each system is carefully designed and packaged to...
-
EZ-ACCESS Transitions® Modular Entry Mat
The Transitions® Modular Entry Mat is a portable rubber threshold mat which is made of 100% recycled rubber and can easily be trimmed or notched to fit various entryway heights. It...
-
PromenAid Handrail System
This handrail is a thing of beauty, but to truly understand its appeal you have to hold one for yourself. Solid, substantial, with a full grip and comfortable feel, PromenAid exceeds...
-
EZ-ACCESS Transitions® Angled Entry Mat
Transitions® Angled Entry Mat – is accommodating for doorways inside and outside. It does not interfere with the door track and works especially well with sliding glass doors. It is...
-
EZ-ACCESS Transitions® Angled Entry Plate
Transitions® Angled Entry Plate – A portable stand-alone threshold plate with a slip-resistant surface which offers superior traction in varying conditions. This single-piece, formed...
-
Hollaender Manufacturing Company ADA Railing Systems
Our ADA railing systems are fully compliant with the Americans with Disabilities Act, and UFAS codes. They’re easy-to-install and made of corrosion resistant aluminum. All...
-
§ 37.42(f)
vertical gap is more than 5/8 inch, measured when the vehicle is at rest, the horizontal and vertical gaps between the car floor and the boarding platform must be mitigated by a bridge plate, ramp...
-
410.6 Doors and Gates
End doors and gates shall provide a clear width 32 inches (815 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1065 mm) minimum....
-
5 [§ 4.7.2]
5 [§ 4.7.2] The transitions on and off the curb ramp are the points where the gutter meets the bottom of the ramp and where the top of the ramp meets the sidewalk....
-
11B-410.6 Doors and gates
End doors and gates shall provide a clear width 32 inches (813 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1067 mm) minimum....
-
11B-410.6 Doors and gates
End doors and gates shall provide a clear width 32 inches (813 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1067 mm) minimum....
-
Doorways [4.8.4]
Recommendation: Ramps and doors should be configured to facilitate wheelchair maneuvering and to prevent open doors from obstructing ramp openings (important along egress routes)....
-
Is there a minimum distance between changes in level?
Ramps and curb ramps, which must be used to span vertical changes greater than ½”, must have level landings and clearances at the tops and bottoms of each run to provide adequate separation...
-
R304.3.2 Running Slope
The running slope of the curb ramp shall be in-line with the direction of sidewalk travel....
-
410.6 Doors and Gates
End doors and gates shall provide a clear width 32 inches (815 mm) minimum. Side doors and gates shall provide a clear width 42 inches (1065 mm) minimum....
-
Simplified Building Concepts: Building a D-Return - ADA Components
Instructional video on building a ramp/stair railing D-return....
