By the same token, certification would not be relevant to construction of a facility for children, if the regulations against which equivalency is measured do not address children´s facilities...
Search Results "Tape Measure"
Filters
Commonly Searched Documents
-
§ 36.606(a)(2)
-
4 [§ 4.7.2]
To measure the gutter slope, place the level in the same position as the arrow in the illustration, with one end where the gutter meets the ramp and the other end towards the street....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
R305.2 Placement
Where the back of curb edge is tooled to provide a radius, the border dimension should be measured from the end of the radius....
-
4.1.6(4)(d)
(ii) If existing thresholds measure 3/4 in (19 mm) high or less, and are beveled or modified to provide a beveled edge on each side, then they may be retained....
-
§ 37.135(d) Phase-in of implementation
If the date for full compliance specified in the plan is after January 26, 1993, the plan shall include milestones, providing for measured, proportional progress toward full compliance....
-
Video Caption Corporation Closed Captioning and Subtitling Services
Just send us your video via tape, Firewire drive, or upload to our FTP server, and we will transcode it to the video format of your choice....
-
Industry Standards
of Certain Walkway Surfaces when Considering Footwear Traction ASTM F 1637-02 Standard Practice for Safe Walking Surfaces ASTM F 1951-99 Wheelchair Work Measurement...
-
Executive Summary
To develop a standard for surface roughness, a literature review on previous studies related to wheelchair vibrations as well as roughness measurement and analysis techniques was completed...
-
Access-Able Designs Wall Mounted Shower Transfer Bench SH-400
Measures 32" W x 21" D x 15" D. Custom sizes available. Must have adequate wall backing. Folds up easily when not in use....
-
Access-Able Designs Adult Dressing Bench D-101-42
Measures 42" W x 20" D. Folds up easily when not in use....
-
Access-Able Designs Rear Mount Tub Transfer Bench w/o Legs SH-414
Measures 29" W x 15" D. Custom sizes available. 5 year warranty....
-
11B-404.2.4.3 Recessed doors and gates
457 mm) of the latch side at an interior doorway, or within 24 inches (610 mm) of the latch side of an exterior doorway, projects more than 8 inches (203 mm) beyond the face of the door, measured...
-
Notes
II The IDeA Center in its research defined wheelchair wheelbase as the distance from the center of the primary drive wheel to the center of the caster measured parallel to the floor....
-
1016.5 Obstacles
This section requires obstacles to not exceed 1/2 inch in height measured vertically to the highest point....
-
Slip Resistance
While different measurement devices and protocols have been developed over the years for use in the laboratory or the field, a widely accepted method has not emerged....
-
Clearance Around Base (M301.4.2 and M302.4.2)
M301.4.2 and M302.4.2 would require the base of the equipment to provide a clearance 6 inches high minimum measured from the floor and 36 inches deep minimum measured from the edge of the...
-
11B-604.7 Dispensers and disposal units
Toilet paper dispensers shall comply with Section 11B-309.4 _|Operation|_ and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the...
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer...
-
§ 36.304(d)(5) Qualified small business
where readily achievable for a given year if, during that tax year, the entity has spent an amount equal to at least one percent (1%) of its gross revenue in the preceding tax year on measures...
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
Cross Slope
Cross Slope—The percentage of rise to length when measuring the trail tread from edge to edge perpendicular to the direction of travel....
-
4.34.3(2)(a) Reach Depth Not More Than 10 in
Where the reach depth to the operable parts of all controls as measured from the vertical plane perpendicular to the edge of the unobstructed clear floor space at the farthest protrusion...
