Search Results "Side Grab Bar"
Filters
Commonly Searched Documents
-
Figure 404.2.4.3(b) Maneuvering Clearance at Recessed Doors and Gates – Drawing from the U.S. Access Board
-
Resting Intervals [1018.8]
Resting intervals are level areas that provide an opportunity for people to stop after a steep segment and recover before continuing on. Resting intervals are required between beach...
-
1018.7.1 Maximum Running Slope and Segment Length
This section requires that the running slope of any segment of a beach access route not be steeper than 1:10 (10%). Where the running slope of a segment a beach access route is...
-
F248.2 Minimum Number
This section requires at least one beach access route to be provided for each 1/2 mile of beach shoreline administered or managed by the entity. The number of beach access routes is...
-
6.11.1 Natural Elements
Accessibility guidelines for protruding objects do not apply to natural elements such as tree branches and rock formations. However, safety regulations or Forest Service construction...
-
6.2.1 Circulation Routes Constructed at Beaches
Beach access routes shall be provided where circulation routes such as boardwalks, walkways, or dune crossings are constructed along or across developed beach sites to provide...
-
F201.4.1 Documentation and Notification When Exceptions Used for Trails and Beach Access Routes
Federal agencies shall document the basis for not fully complying with a specific provision in 1017 or 1018 on a portion of a trail or beach access route based on Exception 1 in 1017...
-
1018.2 Connections
This section requires beach access routes to connect an entry point to the beach to the high tide level at tidal beaches; mean high water level at river beaches; and normal...
-
6.5 Surface
The surface of beach access routes and their related resting intervals shall be firm and stable.
-
406.6 Diagonal Curb Ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
5.4.1.2 Transfer and Positioning Support Location Recommendations for Imaging Equipment with Transfer Surfaces
Both transfer and positioning supports are to be located opposite the transfer side....
-
406.6 Diagonal Curb Ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301)
The transfer surface must be located so the 28-inch long dimension is parallel to the patient scanning/imaging side of the table....
-
406.6 Diagonal Curb Ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing. ...
-
5.2.1.4 Transfer Surface Size for Imaging Equipment
The transfer surface should be located such that the long dimension of 28 inches is located parallel to the patient scanning/imaging side of the table....
-
5.4.1 Transfer Support Location for M301 and M302
NPRM Preamble Discussion: The transfer support would be located on the side of the transfer surface that is opposite the transfer side (M301.2.3 and M302.2.3) similar to the provisions in...
-
11B-404.2.9 Door and gate opening force
Powered doors shall be controlled on both the interior and exterior sides of the doors by sensing devices, push plates, vertical actuation bars or other similar operating devices complying...
-
11B-404.2.9 Door and gate opening force
Powered doors shall be controlled on both the interior and exterior sides of the doors by sensing devices, push plates, vertical actuation bars or other similar operating devices complying...
-
11B-404.2.9 Door and gate opening force
Powered doors shall be controlled on both the interior and exterior sides of the doors by sensing devices, push plates, vertical actuation bars or other similar operating devices complying...
-
11B-703.4.2 Location
Where a tactile sign is provided at a door, the sign shall be located alongside the door at the latch side....
-
11B-703.4.2 Location
Where a tactile sign is provided at a door, the sign shall be located alongside the door at the latch side....
-
11B-703.4.2 Location
Where a tactile sign is provided at a door, the sign shall be located alongside the door at the latch side....
-
M301.2.2 Transfer Surface Size
When the transfer surface is located as described above in “A”, the width of the patient scanning/imaging table (side to side) at the designated transfer location should be 28 inches minimum...
-
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
