Pass through kitchens shall have two entries....
Search Results "Ride Entry"
Commonly Searched Documents
-
11B-804.2.1 Pass through kitchen
-
11B-804.2.1 Pass through kitchen
Pass through kitchens shall have two entries....
-
Are freight or service elevators required to comply?
ASME A17.1 code as those elevators “used primarily for carrying freight and on which only the operator and the persons necessary for unloading and loading the freight are permitted to ride...
-
Alternative Designs
The tub has a non-institutional appearance, a fold-down seat, and a swinging side entry door with a pressurized seal for ease of access....
-
1132A.4 Level floor or landing
Primary entry doors, required exit doors or secondary exterior doors with changes in height between the interior surface or floor level and the exterior surface or floor level shall comply...
-
DOT Response
In addition, the NPRM did not propose to require level-entry boarding as a solution in every instance, permitting other solutions where level-entry boarding was infeasible....
- Turnstile Security Systems Inc. 6000 GB 2 Optical Turnstile Demonstration Video
-
16. Modification to be completed within six months
Modifications to be completed within six months: As agreed between the parties, within six months of the date of entry of this Consent Decree, Defendants shall make the following physical...
-
G. Door Hardware
Is the door hardware (levers, pulls, panic bars, etc.) on all entry doors to accessible guestrooms and other passage doors within the room usable with one hand, without tight grasping, pinching...
-
H. Door Maneuvering Clearance
.: entry door, connecting room door, bathroom doors and other passage doors) in every accessible guestroom/suite, are there at least 18" of clear floor space on the latch side for persons...
-
Site Constraints
An example might include construction of a new infill building with a historic facade which must be maintained (thus predetermining the entry floor level) and where space for a ramp is not...
-
4.13.6 Maneuvering Clearances at Doors
EXCEPTION: Entry doors to acute care hospital bedrooms for in-patients shall be exempted from the requirement for space at the latch side of the door (see dimension “x” in Fig. 25) if the...
-
11B-608.2.3 Alternate roll-in type shower compartments
A 36 inch (914 mm) wide minimum entry shall be provided at one end of the long side of the compartment....
- Turnstile Security Systems Inc. 2 Way Auto Swing Security Gate
- GameTime Roller Table
-
Diversified Woodcrafts Mobile Lab Station with flat top 4352KF
Dovetailed drawers are constructed of plywood and ride on epoxy coated glides. Cupboard door and drawers have locks. Wheelchair accessible from two sides, measures 32"W x 29"H....
- Hill-Rom Uno™ 102 Patient Lift
-
§ 382.40a Boarding assistance for large aircraft
operations with aircraft having a seating capacity of 31 or more passengers at airports with 10,000 or more annual enplanements, in any situation where passengers are not boarded by level-entry...
-
11B-407.2.3.1 Floor designation
A raised star, placed to the left of the floor designation, shall be provided on both jambs at the main entry level. ...
-
11B-608.2.1 Transfer type shower compartments
shower compartments shall be 36 inches (914 mm) by 36 inches (914 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (914 mm) wide minimum entry...
-
407.2.3.1 Floor Designation
A tactile star shall be provided on both jambs at the main entry level. Figure 407.2.3.1 Floor Designations on Jambs of Elevator Hoistway Entrances...
-
804.2.1 Pass Through Kitchen
Pass through kitchens shall have two entries. Figure 804.2.1 Pass Through Kitchens...
-
11B-608.2.3 Alternate roll-in type shower compartments
A 36 inch (914 mm) wide minimum entry shall be provided at one end of the long side of the compartment....
-
M305.3.1.2 Diagnostic Equipment Containing a Wheelchair Space
On diagnostic equipment containing wheelchair spaces with one entry that also serves as the exit, the length of the gripping surface of horizontal standing supports shall be equal to or...