Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
Search Results "Concrete Surface"
-
11B-1008.2.5.3.1 Handrail gripping surfaces
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
§ 38.159(b)(6) Platform surface
(6) Platform surface. The platform surface shall be free of any protrusions of 1/4 inch (6.5 mm) high and shall be slip resistant....
-
T503.3 Steps at Front Doorways
The walking surface on steps serving the front doorway of non-rail vehicles shall be lighted with 2 foot-candles (22 lux) minimum of illumination when the vehicle doors are open....
-
4.26.4 Eliminating Hazards
A handrail or grab bar and any wall or other surface adjacent to it shall be free of any sharp or abrasive elements. Edges shall have a minimum radius of 1/8 in (3.2 mm)....
-
4.26.4 ELIMINATING HAZARDS
A handrail or grab bar and any wall or other surface adjacent to it shall be free of any sharp or abrasive elements. Edges shall have a minimum radius of 1/8 in (3.2 mm)....
-
§ 38.159(c)(2) Ramp surface
(2) Ramp surface....
-
Resting Intervals on Trails
While slope and drainage can be precisely controlled on surfaces that are paved (asphalt, concrete, paving blocks, and so forth) or built with boards (wood planks, heavy timber, concrete...
-
1. Sloped Surfaces
Sloped Surfaces Measuring the slope of a ramp, parking space, walkway, or other ground or floor surface is important to identify whether the surface is accessible....
-
2.5.4 Slope
Where the surface is paved or is elevated above the natural ground, the slope shall not be steeper than 1:48 (2 percent) in any direction. ...
-
5.2.3 Transfer Surface Measurement Recommendation for M301 and M302
5.2.3 Transfer Surface Measurement Recommendation for M301 and M302 Description: The transfer surface size standard has two components: width and depth....
-
Populas Vox Two-Story Adjustable Dual Surface Workstation
Standard Features Adjustment range 24” - 50“ Front surface adjustment range 20” - 57” (4” below, 7” above rear surface), with 15 +/- tilt Power adjusted standard 110V, UL Listed...
-
11B-502.4 Floor or ground surfaces
Advisory 11B-502.4 Floor or ground surfaces. Access aisles are required to be nearly level in all directions to provide a surface for wheelchair transfer to and from vehicles....
-
Engineered Wood Fiber
In addition, there were five sites surfaced with a combination PIP and EWF, and eight sites surfaced with a combination TIL and EWF. ...
-
Section F: Voting Area
_______________________ Location name:______________________ F Within the Voting Area Yes No N/A Comments/Remedies F1 Are floor surfaces...
-
SuperDeck Beach Boardwalk
SuperDeck's low-maintenance decking provides a firm, secure beach boardwalk surface over virtually any terrain....
-
Cross Slope (R302.6) (Section-by-Section Analysis)
In exterior environments, a maximum cross slope of 2 percent is generally accepted as adequate to allow water to drain off paved walking surfaces....
-
Figure 505.6 Horizontal Projections Below Gripping Surface – Drawing from the U.S. Access Board
-
1015.2.1 Glazing
Where the glazing provided does not meet the strength and attachment requirements of Section 1607.8, complying guards shall also be located along glazed sides of open-sided walking surfaces...
-
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302
5.4.8 Transfer Support Gripping Surface Hazard Recommendation for M301 and M302 Description: Gripping surface hazards are sharp or abrasive elements that prevent an individual from sufficiently...
-
1013.2.1 Glazing
Where the glazing provided does not meet the strength and attachment requirements of Section 1607.8, complying guards shall also be located along glazed sides of open-sided walking surfaces...
-
Inpro Corporation JointMaster® 316 Series Single Sightline for Carpet Floor Expansion Joint Covers
The 316 series system was specially designed for continuous flooring types such as carpet and vinyl sheet. Features & Benefits System reduces joint widths of up to 4"...
-
4.1.2(17)
(17) If fixed or built-in seating, tables, or work surfaces are provided in accessible spaces, at least 5 percent, but always at least one, of seating spaces, tables, or work surfaces shall...
-
(4) Adjustability: Method of Measurement
The MDE NPRM proposed that the measurement of the height of the transfer surface for both diagnostic equipment used in the supine, prone, or side-lying position and diagnostic equipment...
