Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
Search Results "Vertical Dispersion"
Filters
Commonly Searched Documents
-
703.2.5 Character Height
-
R405.1 General
Clearances are measured in relation to the usable clear space, not necessarily to the vertical support for an element....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
1008.3.2.3 Transfer Supports
Some examples of supports include a rope loop, a loop type handle, a slot in the edge of a flat horizontal or vertical member, poles or bars, or D rings on the corner posts....
-
7.4.5.1 Size
Vertical alignment at the intersection of the trails that form the T-shaped space shall be nominally level....
-
Parking and Passenger Loading Zones [4.6]
Accessibility also includes the appropriate designation and location of spaces and passenger loading zones, their connection to an accessible route, and vertical clearance for vans....
-
Spout Location [4.15.3]
The trajectory of water flow must be vertically "parallel" or "nearly parallel" to the face of the unit....
-
§ 38.73(d)(1) Requirements
Vertical alignment may be accomplished by vehicle air suspension, automatic ramps or lifts, or any combination....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”. ...
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
A7. Curb Ramps
[ADA Stds 4.7.2] Note: 1:12 is one inch of vertical height for each 12 inches in length. Yes _____ No _____...
-
4.5.2 Changes in Level
Changes in level up to 1/4 in (6 mm) may be vertical and without edge treatment (see Fig. 7(c))....
-
4.5.2 CHANGES IN LEVEL
Changes in level up to 1/4 in (6 mm) may be vertical and without edge treatment (see Fig. 7(c))....
-
Handrails [§504.6, §505]
A vertical clearance 9” minimum between upper and lower handrails will help prevent entrapment....
-
Where Required: Multi-Story Buildings and Facilities [§206.2.3]
provisions in the Standards still apply to stories and mezzanines not served by an accessible route elevators provided anyway must fully comply (as standard or LULA elevators) vertical...
-
§ 38.23(b)(8) Platform entrance ramp
loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, measured on level ground, for a maximum rise of 3 inches, and the transition from roadway or sidewalk to ramp may be vertical...
-
Location: ADA Standard Section 206.3
Section 206.3 covers scoping requirements in the most current ADA Standards for the required locations of accessible routes.
-
Corbin Russwin Inc. ED7000 Series Narrow Stile Crossbar Exit Device
The ED7000 Series are available as Rim, Surface Vertical Rod, Mortise and Concealed Vertical Rod devices. ...
-
PDQ 4200 Series Exit Device Door Hardware
The American Eagle 4200 Series is a rim or surface vertical rod exit device....
-
Husky 24" Line Generator Digital Laser Level
This level may use indoors or out for horizontal (level), vertical (plumb) and square alignment projects....
-
Clearances
The 80-inch minimum vertical clearance requirement remains for circulation areas and accessible routes in the queue line and load and unload areas....
-
§ 38.113(d)(1) Requirements
Vertical alignment may be accomplished by car air suspension, platform lifts or other devices, or any combination....
