stall and shower seat where such facilities are provided, as required by §100.205(c)(3)(iii)....
Search Results "Shower Curb"
Filters
Commonly Searched Documents
-
Guidelines for Requirement 6
-
Floor or Ground Surfaces: ADA Standard Section 502.4
Section 502.4 covers the current ADA Standards for the floor or ground surfaces of accessible parking spaces.
-
Figure 608.2.3 Alternate Roll-In Type Shower Compartment Size and Clearance – Drawing from the U.S. Access Board
-
Guest Rooms
When designing or remodeling rooms, strongly consider increasing the number of roll-in/walk-in shower rooms. Surveys indicate a vast majority of guests shower rather than bathe....
-
11B-608.3 Grab bars
Grab bars shall not be required to be installed in a shower located in a bathing facility for a single occupant accessed only through a private office, and not for common use or public use...
-
11B-608.3 Grab bars
Grab bars shall not be required to be installed in a shower located in a bathing facility for a single occupant accessed only through a private office, and not for common use or public use...
-
11B-608.3 Grab bars
Grab bars shall not be required to be installed in a shower located in a bathing facility for a single occupant accessed only through a private office, and not for common use or public use...
-
Proline Drain
QuickDrain USA is the leader in linear shower drains. Our standard linear shower drain kits eliminate the old-fashioned center shower drain and are fast and easy to install....
-
4.3.2 Seat Height
4.3.2 Seat Height Seat height is an important dimension for establishing the height of built-in seating, toilet heights, tub heights, shower seat heights and other transfer related surfaces...
-
Section C: Exterior Route
(§307.4) C8 If the route crosses a curb, is there a curb ramp that is at least 36" wide with a slope no more than 1:12?...
-
11B-224.1.2 Guest room doors and doorways
Exception: Shower and sauna doors in guest rooms that are not required to provide mobility features complying with Section 11B-806.2 shall not be required to comply with Section 11B-404.2.3...
-
11B-224.1.2 Guest room doors and doorways
Exception: Shower and sauna doors in guest rooms that are not required to provide mobility features complying with Section 11B-806.2 shall not be required to comply with Section 11B-404.2.3...
-
11B-224.1.2 Guest room doors and doorways
Exception: Shower and sauna doors in guest rooms that are not required to provide mobility features complying with Section 11B-806.2 shall not be required to comply with Section 11B-404.2.3...
-
Accessible Sidewalks 1: Pedestrians who use Wheelchairs
Requires the Registered User plan or above. Login! -
Bobrick Two-Wall Tub/Shower Toilet Compartment Grab Bar B-68137
36" W x 54" D (91 x 137cm), 1-1/2" (38mm) dia. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick Two-Wall Tub/Shower Toilet Compartment Grab Bar B-5837
36" W x 54" D (91 x 137cm), 1-1/4" (32mm) dia. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Requirement 6. Reinforced walls for grab bars.
stall and shower seat, where such facilities are provided....
-
Q8: Curb Ramp Replaced as Part of a Resurfacing Alteration and Adjacent Sidewalk
Q8: If an existing curb ramp is replaced as part of a resurfacing alteration, is there an obligation to address existing obstacles on the adjacent sidewalk at the same time? A8: No....
-
610 Seats
[See subsections ...]
-
610 Seats
[See subsections ...]
-
610 Seats
610 Seats
-
11B-809.10.6.5 Thresholds
Where provided thresholds shall be 2 inches (51 mm) maximum in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from the...
-
American Standard Colony Soft Diverter & Personal Trim Kit
A handheld personal shower is invaluable for rinsing yourself, bathing kids and cleaning the bathtub....
-
Q5.) What dimensions and conditions can practitioners reasonably consider to be compliant when the conditions, as constructed, do not meet the technical requirements exactly and there are no official, published, industry-developed tolerances?
of the materials and processes, David Ballast generally recommends a tolerance of 0.5% in the cross slope direction and 1.0% in the direction of travel for concrete or asphalt ramps and curb...
