Sites, buildings, facilities, and elements are exempt from these requirements to the extent specified by 11B-203....
Search Results "Fire-Building Surface"
Filters
Commonly Searched Documents
-
11B-203.1 General
-
11B-203.1 General
Sites, buildings, facilities, and elements are exempt from these requirements to the extent specified by 11B-203....
-
11B-203.1 General
Sites, buildings, facilities, and elements are exempt from these requirements to the extent specified by 11B-203....
-
F105.2.4 ICC/IBC
International Building Code, 2000 Edition (see F207.1, F207.2, F216.4.2, F216.4.3, and 1005.2.1). International Building Code, 2001 Supplement (see F207.1 and F207.2)....
-
105.2.4 ICC/IBC
International Building Code, 2000 Edition (see 207.1, 207.2, 216.4.2, 216.4.3, and 1005.2.1). International Building Code, 2001 Supplement (see 207.1 and 207.2)....
-
105.2.4 ICC/IBC
International Building Code, 2000 Edition (see 207.1, 207.2, 216.4.2, 216.4.3, and 1005.2.1). International Building Code, 2001 Supplement (see 207.1 and 207.2)....
-
Site Impracticality Determinations
Other commenters stated that single buildings on a site should be subject to the same analysis as multiple buildings on a site....
-
DSA Summary of 2016 California Building Code Changes for Accessibility
Summary of 2016 California Building Code Changes for Accessibility The following changes in the 2016 California building codes (California Code of Regulations, Title 24) amended...
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved.
-
Shredded Rubber
The surface material used as a play safety surface has gained some popularity as a means to reuse tires. ...
-
1014.3.2 Slope
The slope of the floor surface shall not be steeper than 1:48 in any direction....
-
1014.3.2 Slope
The slope of the floor surface shall not be steeper than 1:48 in any direction....
-
4.3.5 Transfer Height
Tent platform surfaces that are not the same elevation as the ORAR shall be between 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the floor or ground surface adjacent to...
-
Scoping [4.1.2(4), 4.1.3(3)]
Requirements in 4.5 apply to accessible routes and spaces, including ramps, elevators, platform lifts, and clear floor space. These requirements apply to interior and exterior...
-
F202.3.2 Extent of Application
An alteration of an existing element, space, or area of a building or facility shall not impose a requirement for accessibility greater than required for new construction....
-
Cross Slope: ADA Standard Section 405.3
Section 405.3 covers the current ADA Standards for cross slope requirements on ramps.
-
603 Toilet and Bathing Rooms
(This section is to be used for toilet buildings with a single riser such as SSTs, but not for pit toilets. See definition of pit toilet in Technical Provisions section of FSORAG.)...
-
4.1.7(2)(e)
., books, should be no higher than 44 in (1120 mm) above the floor surface....
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3....
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3....
-
11B-904.3.3 Check writing surfaces
Where provided, check writing surfaces shall comply with Section 11B-902.3....
-
The Division of the State Architect and Department of Rehabilitation-Teleconference Transcript, September 1, 2016
The purpose of this meeting was to solicit comments and suggestions for potential amendments to the accessibility provisions of the California Building Code....
-
11B-226.3 Dining surfaces exceeding 34 inches in height
Where food or drink is served for consumption at a counter exceeding 34 inches (864 mm) in height, a portion of the main counter 60 inches (1525 mm) minimum in length shall be...
-
11B-226.3 Dining surfaces exceeding 34 inches in height
Where food or drink is served for consumption at a counter exceeding 34 inches (864 mm) in height, a portion of the main counter 60 inches (1525 mm) minimum in length shall be...
