Curb ramps and blended transitions must comply with the technical requirements in R302.7 and R304. Ramps must comply with the technical requirements in R407....
Search Results "Curb Cut"
Commonly Searched Documents
- 
    
  
  Components (R302.2) (Section-by-Section Analysis)
  
- 
    
  
  ALTERNATIVES TO BARRIER REMOVAL
  Examples of alternatives to barrier removal include, but are not limited to, the following actions -- §36.305(b)(1) Providing curb service or home delivery; §36.305(b)(2) Retrieving... 
- 
    
  
  11B-308.3.1 Unobstructed
  Operable parts of fuel dispensers shall be permitted to be 54 inches (1372 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs... 
- SafetyStepTD Ramp-Up Detectable Warning System
- Florestone 35-62H Barrier-Free Shower
- Beneficial Designs Public Rights of Way Assessment Process (PROWAP)
- 
    
  
  308 Reach Ranges
  Gas pumps are often located on curbs at least 6 inches high for safety reasons.... 
- 
    
  
  308.3.1 Unobstructed
  Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs... 
- 
    
  
  10.2.1(1)
  are constructed at bus stops, bays or other areas where a lift or ramp is to be deployed, they shall have a firm, stable surface; a minimum clear length of 96 inches (measured from the curb... 
- 
    
  
  308.3.1 Unobstructed
  Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs... 
- 
    
  
  308.3.1 Unobstructed
  Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs... 
- 
    
  
  11B-308.3.1 Unobstructed
  Operable parts of fuel dispensers shall be permitted to be 54 inches (1372 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs... 
- 
    
  
  11B-303.3 Beveled
  Changes in level exceeding 1/2 inch (13 mm) must comply with Sections 11B-405 (Ramps) or 11B-406 (Curb Ramps). ◼ ... 
- American Academy of Physical Medicine and Rehabilitation (AAPM&R)
- 
    
  
  1005.3 Edge Protection
  In such a design, curbs or barriers are not required.... 
- 
    
  
  1005.3 Edge Protection
  In such a design, curbs or barriers are not required.... 
- 
    
  
  Section 2. Accessible route
  Exterior accessible routes may include parking access aisles, curb ramps, walks, ramps and lifts.... 
- 
    
  
  308.3.1 Unobstructed
  Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs... 
- 
    
  
  1005.3 Edge Protection
  In such a design, curbs or barriers are not required.... 
- 
    
  
  §100.201 Accessible route
  Exterior accessible routes may include parking access aisles, curb ramps, walks, ramps, and lifts.... 
- 
    
  
  11B-1005.3 Edge protection
  In such a design, curbs or barriers are not required.... 
- 
    
  
  Q6.)  How important is the method of measurement in considering the tolerances allowable in finished construction?
  For ramps and curb ramps, DOJ has issued two technical assistance documents that show how to measure slopes. ... 
- 
    
  
  308.3.1 Unobstructed
  Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs... 
- 
    
  
  Compliance requirements
  address the design, construction, and alteration of pedestrian facilities in the public right-of-way, including sidewalks, pedestrian street crossings, pedestrian overpasses and underpasses, curb... 
