Where the back of curb edge is tooled to provide a radius, the border dimension should be measured from the end of the radius....
Search Results "Back Wall"
-
R305.2 Placement
-
Is color contrast required for stair nosings?
The ASME A17.1 code requires escalator steps to be demarcated by yellow lines 2” wide maximum along the back and sides....
-
408.4.6 Car Controls
Control panels shall be centered on a side wall....
-
408.4.6 Car Controls
Control panels shall be centered on a side wall....
-
704.2.2 Types III, IV and V construction
Projections from walls of Type III, IV or V construction shall be of any approved material....
-
11B-411.4.10 Support rail
Support rails complying with Section 11B-407.4.10 shall be provided on at least one wall of the car....
-
4.9.4(3)
(3) The clear space between handrails and wall shall be 1‒1/2 in (38 mm)....
-
4.8.5(3)
(3) The clear space between the handrail and the wall shall be 1 - 1/2 in (38 mm)....
-
11B-411.4.10 Support rail
Support rails complying with Section 11B-407.4.10 shall be provided on at least one wall of the car....
-
11B-411.4.10 Support rail
Support rails complying with Section 11B-407.4.10 shall be provided on at least one wall of the car....
-
11B-813.2.1 Adult changing table
Adult changing tables shall be fixed to the floor or a wall and shall comply with Section 11B-813.2.1....
-
Kitchens and Kitchenettes
Section 4.34.6 requires a clearance between opposing base cabinets, counters, appliances, or walls of at least 40 inches except in a U-shaped kitchen where the minimum clearance is 60 inches...
-
Gamco Welded Frame Mirrors - A-Series
Back Panel - fabricated of galvanized steel with tab lock and snap lock design slots formed to receive wall hanger tabs....
-
IDEA Center
For lateral reach we also calculated reach to a second plane set 254 -610 mm (10 - 24 in.) back from the lateral most point (not reported here)....
-
American Specialties Channel Frame Mirror 0620
1/2" x 1/2" x 1/2" (13 x 13 x 13 mm) 20 gauge type 304 satin finish stainless steel channel is a one piece roll formed member that encases mirror and backing revealing a tight mitered corner...
-
704.9 Vertical separation of openings
Openings in exterior walls in adjacent stories shall be separated vertically to protect against fire spread on the exterior of the buildings where the openings are within 5 feet (1524 mm...
-
11B-607.4 Grab bars
Where separate grab bars are required on adjacent walls at a common mounting height, an L-shaped or U-shaped grab bar meeting the dimensional requirements of Section 11B-607.4.1 or 11B-607.4.2...
-
§ 38.93(d)(3) Exception
Where platform set-backs do not allow the horizontal gap or vertical alignment specified in paragraph (d)(1) or (d)(2) of this section, car, platform or portable lifts complying with §38.95...
-
Medical Diagnostic Equipment Accessibility Standards Sub Committee Recommendations Stretcher Final Report
Criteria Applies Supine, prone, or side-lying position (M301) Transfer surface, including height, size, and transfer sides Transfer supports, stirrups, and head and back...
-
11B-408.4.6 Car controls
Control panels shall be centered on a side wall....
-
H18
Is the centerline of the toilet 18 inches from the adjacent side wall? [ADA Standards § 4.16.2; 4.17.3] Yes No...
-
M16
Is the centerline of the toilet 18 inches from the adjacent side wall? [ADA Standards §§ 4.16.2; 4.17.3] Yes No...
-
7(1)(b)
(b) Clearance between counters and all opposing base cabinets, countertops, appliances or walls is at least 40 inches....
-
Grab Bar
Grab Bar—A bar attached to a wall to provide a handgrip for steadying oneself or to assist in transferring across short distances....
