During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
Search Results "Pull Side"
-
M305.2.3 Height
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports. However, in the MDE NPRM preamble the Access Board repeatedly noted that...
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The proposed rule did not provide specific requirements for the cross section of transfer supports. However, in the MDE NPRM preamble, the Access Board noted that it was considering...
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302 Description: Transfer supports may contain elements to provide structural support or prevent...
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and...
-
5.4.2 Transfer Support Length for M301 and M302
5.4.2 Transfer Support Length for M301 and M302 Description: Transfer support length applies to the gripping surface of the support, that portion of the support used to grasp or...
-
5.7.1 Lift Compatibility Clearance in Base for M301
5.7.1 Lift Compatibility Clearance in Base for M301 Description: For portable floor lifts to be effective, they must deploy at diagnostic equipment such that the boom of the lifts...
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position.
-
Curb Ramp Requirements [§406]
Curb Ramp Requirements [§406]
-
804.6.5.1 Side-Hinged Door Ovens
Side-hinged door ovens shall have the work surface required by 804.3 positioned adjacent to the latch side of the oven door....
-
804.6.5.1 Side-Hinged Door Ovens
Side-hinged door ovens shall have the work surface required by 804.3 positioned adjacent to the latch side of the oven door....
-
Brey-Krause Concealed Mounting Security / Anti Suicide Grab Bars
The concealed mount anti-ligature grab bars are fabricated from 18 gauge stainless steel. The flange is constructed from 11 gauge stainless steel and is three inches in diameter....
-
Behavioral Safety Products #GB350 Suicide Resistant Safety Grab Bar with Full Closure Plate
Product Description We offer this suicide resistant grab bar in seven lengths: 18", 24", 30", 32", 36", 42", and 48". All lengths except for the 18" and 32" are available for...
-
T208.2.2 Doorways on Two Sides of vehicle
Where non-rail vehicles have doorways on two sides, a passenger access route shall connect each wheelchair space to doorways on both sides of the vehicle that provide a means of accessible...
-
Is compliance on both sides of a door or gate required when it is usable only from one side?
No, compliance is not required on both sides of those doors or gates that can be used in one direction only. Compliance is required only on the usable side....
-
Comparison of Single-User Toilet Room “Pairs” With Fixtures Side-by-Side: Plan 2C
Comparison of Single-User Toilet Room “Pairs” With Fixtures Side-by-Side: Plan 2C 2010 Standards Plan-2C Pair: 2010 Standards with In-Swinging Doors...
-
11B-404.2.4.1 Swinging doors and gates
Perpendicular to doorway Parallel to doorway (beyond latch side unless noted) From front Pull 60 inches (1524 mm) 18 inches (457...
-
11B-404.2.4.1 Swinging doors and gates
Perpendicular to doorway Parallel to doorway (beyond latch side unless noted) From front Pull 60 inches (1524 mm) 18 inches (457...
-
M301.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A. A low transfer position...
-
M301.2.2 Sunset
The low transfer position height, Item A of M301.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register].
-
M301.2.2 Sunset Provision (Section-by-Section Analysis)
As discussed in Section IV.B.1.a. (Significant Changes – Transfer Surface Adjustability), this is a new provision that was added to the final rule in conjunction with the new...
-
Bradley Center-Pull Towel Dispenser 2479 10 Side Elevation
Requires the Premium User plan or above. (Login or upgrade your account!) -
The UpScale Medical Exam Table
Learn more at http://medicalaccessibility.com/ Two Products in One - Combines a height-adjustable exam table with an accessible weight scale to save money and save...
-
Stable and rock solid. See for yourself!
Learn more at http://medicalaccessibility.com/ Two Products in One - Combines a height-adjustable exam table with an accessible weight scale to save money and save...
