Federal agencies shall document the basis for not fully complying with a specific provision in 1017 or 1018 on a portion of a trail or beach access route based on Exception 1 in 1017...
Search Results "Grab Bar Fitting"
-
F201.4.1 Documentation and Notification When Exceptions Used for Trails and Beach Access Routes
-
1018.2 Connections
This section requires beach access routes to connect an entry point to the beach to the high tide level at tidal beaches; mean high water level at river beaches; and normal...
-
6.5 Surface
The surface of beach access routes and their related resting intervals shall be firm and stable.
-
Wikk Industries Ingress'r Automatic Door Control
and retrofit installations uncomplicated Black ABS cap attached with security screws (supplied) for wireless transmission Adaptable for 1/2” conduit in surface wiring applications Fits...
-
Attachment I
The rear grab bar is mounted with the closer end 21 inches from the side wall. ...
-
Methodology
This study was approved by the University of Pittsburgh's Institutional Review Board and all participants provided informed consent before participating in any test procedures.
-
1018.4 Clear Width
The clear width of beach access routes shall be 60 inches (1525 mm) minimum. EXCEPTION: At dune crossings, the clear width of beach access routes that are not removable shall be...
-
Surface [1018.3]
The surface of beach access routes and resting intervals must be firm and stable. Sand is not a firm and stable surface. Additional information on firm and stable surfaces is...
-
Location [F248.3]
Beach access routes must coincide with or be located in the same general area as pedestrian access points that serve the beach.
-
Surface and Clear Tread Width on Beach Access Routes
A beach access route must have a firm, stable surface, and have a clear tread width of 60 inches (1,525 millimeters) minimum.
-
Slopes and Resting Intervals for Beach Access Routes
Running slope, also referred to as "grade," is the lengthwise slope of a beach access route, parallel to the direction of travel. Sections of beach access route of any length are...
-
6.6 Clear Width
The clear width of beach access routes shall be 60 inches (1525 mm) minimum. Exception: At dune crossings, the clear width of beach access routes that are not removable shall...
-
F248.3 Location
This section requires beach access routes to coincide with or be located in the same general area as pedestrian access points to the beach.
-
1018.4 Clear Width
The clear width of beach access routes shall be 60 inches (1525 mm) minimum. EXCEPTION: At dune crossings, the clear width of beach access routes that are not removable shall be...
-
General: ADA Standard Section 226.1
Section 226.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for dining surfaces and work surfaces.
-
11B-226.1 General
Where dining surfaces are provided for the consumption of food or drink, at least 5 percent of the seating spaces and standing spaces at the dining surfaces shall comply with Section...
-
11B-226.1 General
Where dining surfaces are provided for the consumption of food or drink, at least 5 percent of the seating spaces and standing spaces at the dining surfaces shall comply with Section...
-
H. Men's Spa and Fitness Center Locker Room
Men's Spa and Fitness Center Locker Room: (1) Defendants will install a vertical, self-operating lift in the Men's Spa whirlpool in order to permit access for persons with disabilities...
-
Delta ADA Grab Bar Hand Shower Mount U6300-WH
Product Features and Benefits Fits 1 1/2″ or 11/4″ grab bars Rotatable hand shower mount Lifetime Faucet and Finish Warranty ADA Compliant...
-
11B-606.2 Clear floor space
A parallel approach complying with Section 11B-305 shall be permitted to a kitchen sink in a space where a cook top or conventional range is not provided and to wet bars. 2. Reserved...
-
11B-606.2 Clear floor space
A parallel approach complying with Section 11B-305 shall be permitted to a kitchen sink in a space where a cook top or conventional range is not provided and to wet bars. 2. Reserved...
-
Wikk Industries Inc. Bollard With Push Plate PART#BPRT126SMFT32D (630)
12”x6”x42” Tall, 7ga. Formed 304 Satin Stainless Steel US32D (630), Surface mount with concealed mounting base, 1 prep for INGRESS’R ® ADA switch (630), Welded Flat top. Shown on...
-
SDC Bollard Post with Push Plate or Touch Panel
Alternative to wall mounted access control or switches for entry doors. Bollard post provide visibility and meet accessibility guidelines. Practical solution for surface mount or...
-
Wikk Industries Inc. PART#BPS SM-INGR CLEAR (628) with I36-3 CLEAR (628)
6”X6”X42” Tall, Clear Anodized Aluminum (628), Surface mount with concealed mounting base, 1 prep for INGRESS’R® ADA switch, Removable Black ABS cap Shown on the bollard- I36-3...
