(2) The accessible route required by 10.3.2(1) shall include the features specified in 10.3.1(1), (4)-(9), (11)-(15), and (17)-(19).
Search Results "Support Rail"
-
10.3.2(2)
-
§ 38.105(b)
(b) Characters on signs required by paragraph (a) shall have a width-to-height ratio between 3:5 and 1:1 and a stroke width-to-height ratio between 1:5 and 1:10, with a minimum...
-
§ 38.125(c)(5) Slope
(5) Slope. Ramps or bridge plates shall have the least slope practicable. If the height of the vehicle floor, under 50% passenger load, from which the ramp is deployed is 3 inches or...
-
Railings
Railings Where railings, guards, or handrails are provided on a fishing pier or platform, they must meet ADAAG provisions....
-
T302 Walking Surfaces
Another commenter, a transportation research center, noted that the wheelchair securement systems used in many non-rail vehicles—especially small buses and vans—are floor mounted and have...
-
M305.2.7 Clearance (Section-by-Section Analysis)
In the MDE NPRM, the Access Board did not provide any specific requirements for clearances around the transfer support....
-
d. Unobstructed Transfer
Six of the eleven commenters who responded to this question supported permitting equipment parts to extend up to three inches horizontally beyond the edge of the transfer surface....
-
M305.2.2 Length
The length of transfer supports shall comply with M305.2.2.1 or M305.2.2.2....
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports....
-
M305.2.1 Location
Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the transfer...
-
M305.2.6 Gripping Surface
Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
M305.2.3 Fittings
Transfer supports shall not rotate within their fittings....
-
F206.4.4.1 Location
In transportation facilities, where different entrances serve different transportation fixed routes or groups of fixed routes, at least one public entrance serving each fixed route...
-
11B-810.6.2 Routes and destinations
Lists of stations, routes and destinations served by the station which are located on boarding areas, platforms, or mezzanines shall comply with Section 11B-703.5 _|Signs; Visual...
-
810.6.2 Routes and Destinations
Lists of stations, routes and destinations served by the station which are located on boarding areas, platforms, or mezzanines shall comply with 703.5. At least one tactile sign...
-
§ 38.75(c)
(c) Characters on signs required by paragraphs (a) or (b) of this section shall have a width-to-height ratio between 3:5 and 1:1 and a stroke width-to-height ratio between 1:5 and...
-
§ 38.111(d)
(d) Passenger coaches or food service cars shall have the number of spaces complying with §38.125(d)(2) of this part and the number of spaces complying with §38.125(d)(3) of this...
-
11B-810.6.2 Routes and destinations
Lists of stations, routes and destinations served by the station which are located on boarding areas, platforms, or mezzanines shall comply with Section 11B-703.5 _|Signs; Visual...
-
11B-810.6.2 Routes and destinations
Lists of stations, routes and destinations served by the station which are located on boarding areas, platforms, or mezzanines shall comply with Section 11B-703.5. At least one...
-
810.6.2 Routes and Destinations
Lists of stations, routes and destinations served by the station which are located on boarding areas, platforms, or mezzanines shall comply with 703.5. At least one tactile sign...
-
810.6.2 Routes and Destinations
810.6.2 Routes and Destinations. Lists of stations, routes and destinations served by the station which are located on boarding areas, platforms, or mezzanines shall comply with...
-
M305.2.8 Fittings
Transfer supports shall not rotate within their fittings when in place for transfer....
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The proposed rule did not provide specific requirements for the cross section of transfer supports....
-
American Stair Corp. Standard Railings
Railings provide safety and design continuity. American Stair's standard railings are precision manufactured from quality welded steel. ...
