The space between the grab bar and projecting objects below and at the ends shall be 1½ inches (38 mm) minimum....
Search Results "Horizontal Projection"
Filters
Commonly Searched Documents
-
11B-609.3 Spacing
-
3. Data Overview
Section 3.1 provides an overview of the total number of movie theater auditoriums operating in the United States in 2015, the types of venues they operate in (venue type), the projected...
-
6.1 General
The basis for the determination shall be documented and maintained with the records of the construction or alteration project. Exception 2....
-
11B-609.3 Spacing
The space between the grab bar and projecting objects below and at the ends shall be 1½ inches (38 mm) minimum....
-
11B-609.3 Spacing
The space between the grab bar and projecting objects below and at the ends shall be 1½ inches (38 mm) minimum....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
404.2.4.3 Recessed Doors and Gates
Maneuvering clearances for forward approach shall be provided when any obstruction within 18 inches (455 mm) of the latch side of a doorway projects more than 8 inches (205 mm) beyond the...
-
§8.27(a)
(a) Owners and managers of multifamily housing projects having accessible units shall adopt suitable means to assure that information regarding the availability of accessible units reaches...
-
1134A.6, Item 1.2
A water closet may project a maximum of 12 inches (305 mm) into the opening provided that a minimum of 36 inches (914 mm) clear space is maintained between the water closet and the shower...
-
Extensions
Extensions are not required in alterations if they project into cross circulation paths. Extensions must be rounded or returned to the walls, floors, or posts....
-
Best Practices in the Design of Toileting and Bathing Facilities for Assisted Transfers
Sanford, Project Director Atlanta Research and Education Foundation Prepared for: US Access Board The products shown in this report are only intended to serve as illustrated examples...
-
Built-Up Curb Ramps
Built-up curb ramps are permitted, but they cannot project in parking spaces, access aisles, or vehicle traffic lanes....
-
4 - Best practices for construction observation
For large projects for where extensive accessible surfaces are required, early checking should be done to suggest needed adjustments to construction techniques....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
Fixed position maps and kiosks
While it is normally more convenient and practical to mount these maps on vertical surfaces, as is typical for publicly displayed maps, it is better to place tactile maps on a horizontal...
-
Location and Size
The side rails are 20 inches minimum in length, 6 inches minimum in height above the table surface, and 1 inch measured horizontally from the adjacent edge of the table surface....
-
703.5.5 Character Height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
M305.3 Standing Supports (Section-by-Section Analysis)
This provision has been reorganized in the final rule into requirements for length and height, as opposed to vertical and horizontal....
-
703.5.5 Character Height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
703.5.5 Character Height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
703.5.5 Character Height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
11B-405.9 Edge protection
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (12.7 mm) maximum within 10 inches (254 mm) horizontally of the minimum landing area...
-
1007.6 Areas of refuge
elevator lobby is used as an area of refuge, the shaft and lobby shall comply with Section 1022.10 for smokeproof enclosures except where the elevators are in an area of refuge formed by a horizontal...