Where boarding piers are provided at boat launch ramps, at least 5 percent, but no fewer than one, of the boarding piers shall comply with Section 11B-1003.3.2. ...
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
11B-235.3 Boarding piers at boat launch ramps
-
11B-235.3 Boarding piers at boat launch ramps
Where boarding piers are provided at boat launch ramps, at least 5 percent, but no fewer than one, of the boarding piers shall comply with Section 11B-1003.3.2....
-
11B-405.7.2.1
Where the ramp width is less than the top landing width additional landing length may be necessary to accommodate handrail extensions required to be in the direction of the ramp run without...
-
Q7: Curb Ramp for a Sidewalk that is Not Made of Concrete or Asphalt
Q7: Is a curb ramp required for a sidewalk that is not made of concrete or asphalt?...
-
11B-406.5.2 Width
The clear width of curb ramp runs (excluding any flared sides), blended transitions, and turning spaces shall be 48 inches (1219 mm) minimum....
-
A4.5.1 GENERAL
Wheelchairs can be propelled most easily on surfaces that are hard, stable, and regular....
-
11B-305.2 Floor or ground surfaces
Floor or ground surfaces of a clear floor or ground space shall comply with Section 11B-302....
-
4.8.5* Handrails
If a ramp run has a rise greater than 6 in (150 mm) or a horizontal projection greater than 72 in (1830 mm), then it shall have handrails on both sides....
-
Cargill, Incorporated SafeLane® Surface Overlay CA-48
SafeLane® Surface Overlay CA-48 Commercial contractors, property managers and other private winter maintenance service providers require the same anti-skid, anti-icing and infrastructure...
-
11B-406.5.6 Grade breaks
Grade breaks at the top and bottom of curb ramp runs shall be perpendicular to the direction of the ramp run....
-
11B-406.5.6 Grade breaks
Grade breaks at the top and bottom of curb ramp runs shall be perpendicular to the direction of the ramp run....
-
11B-406.5.6 Grade breaks
Grade breaks at the top and bottom of curb ramp runs shall be perpendicular to the direction of the ramp run....
-
409.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
409.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
Rollability and Smoothness of Walking Surfaces
surfaces....
-
M301.2 Transfer Surface (Section-by-Section Analysis)
This is an introductory section.
-
Non-Circular Cross Section and Clearance (§505.5, §505.7)
Non-Circular Cross Section and Clearance (§505.5, §505.7)
-
11B-406.5.3 Landings
Exception: Parallel curb ramps shall not be required to comply with Section 11B-406.5.3. Advisory 11B-406.5.3 Landings....
-
R304.5.2 Grade Breaks
Grade breaks at the top and bottom of curb ramp runs shall be perpendicular to the direction of the ramp run....
-
11B-306.2.3 Minimum required depth
The toe clearance shall extend 19 inches (483 mm) minimum under built-in dining and work surfaces required to be accessible by Section 11B-226.1....
-
11B-406.5.3 Landings
A level landing, 48” deep and at least as wide as the curb ramp, is required at the top of a curb ramp. ...
-
Clear Width [§405.5]
Clear Width [§405.5] Ramp runs must have a clear width of 36” minimum (measured between handrails where provided)....
-
405.1 General
Ramps on accessible routes shall comply with 405....
-
405.1 General
Ramps on accessible routes shall comply with 405....
