Amusement rides designed primarily for children, amusement rides that are controlled or operated by the rider, and amusement rides without seats, are not required to provide wheelchair spaces...
Search Results "Children's Dimension"
Filters
Commonly Searched Documents
-
11B-216.12 Amusement rides
-
Family members and friends as interpreters. (Section-by-Section Analysis)
Some representatives of pediatricians objected to this provision, stating that parents of children with disabilities often know best how to interpret their children's needs and health status...
-
Altered Rides
Rides designed for children, assisted on and off by an adult, are only required to provide an accessible route to the ride and a turning space in the load and unload area....
-
Other Road and Shared Use Path Users
Electric toys for children-Small electric devices, usually with four wheels, often designed to emulate full size adult motor vehicles....
-
Section 37.27 Transportation for Elementary and Secondary Education Systems
This extension also applies to transportation of pre-school children to Head Start or special education programs which receive Federal assistance....
-
11B-903.4 Back support
The bench shall provide for back support or shall be affixed to a wall along its long dimension....
-
Drinking Fountains for Standing Persons
This commenter advised that a 38 inch height will accommodate units that are intended to serve both adults and children. Response....
-
Kitchen Electrical/Lighting/Mechanical
Low voltage lighting saves energy Low voltage lights also improves visual acuity in cabinets Hot water floor heating to keep heat low in the room for children, shorter people...
-
Project Goals
Adaptable: to the needs of tall and short users, older people, children, and those with low vision, reduced mobility or low hearing. ...
-
Inpro Corporation Endurant® Stainless Steel Straight Grab Bar
FEATURES: 1 1/4" grab bar diameter allows for a better grip for women and children Offers a secure and safe installation by giving the installer the flexibility to choose...
-
Table of Contents
CHAPTER 1: APPLICATION AND ADMINISTRATION 101 Purpose 102 Dimensions for Adults and Children 103 Equivalent Facilitation 104 Conventions 105 Referenced Standards 106 Definitions...
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
11B-407.4.7.2 Keypads
The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 11B-703.3.1 _|Braille Dimensions|_....
-
11B-302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel....
-
1. Measuring Tape
You will generally not need to measure dimensions in increments of less than ¼ inch....
-
5.4.2.1 Transfer Support Length Recommendation for Stretchers
5.4.2.1 Transfer Support Length Recommendation for Stretchers On Stretchers, the transfer surface is oriented along the long dimension of the surface on which patients are positioned...
-
5.4.4.2 Transfer Support Distance from Transfer Surface Recommendation for Imaging Equipment
Rationale for the Recommendation The Committee decided to follow the recommended 1 1/2inch proposal but included a 3-inch dimension to accommodate movement of the support....
-
Openings in Beach Access Routes
Place elongated openings more than a quarter of an inch wide with the long dimension perpendicular or diagonal to the primary direction of travel (see figure 44)....
-
Openings in Outdoor Recreation Access Route Surfaces
Place elongated openings that are more than a quarter of an inch wide with the long dimension perpendicular or diagonal to the primary direction of travel (figure 44)....
-
Knee Clearance: Clearance as Measured from Anterior-Most Point - Manual Wheelchair
It references dimensions of clearance height and depth to the forward-most point on the person or mobility device (e.g., toe, footrest)....
-
Knee Clearance: Clearance as Measured from Dorsal Foot Point - Manual Wheelchair
It references dimensions of clearance height and depth to the dorsal foot point on a person (e.g., top of ankle)....
-
1.2.1
1.2.1 Use the plus - or - minus symbol (±) after a dimension when it must be made clear what the expected tolerance is. This should be coordinated with the specification requirements....
-
11B-407.4.7.2 Keypads
The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 11B-703.3.1 _|Braille Dimensions|_....
-
8.1 Excluded Populations Needing Future Attention
The numbers of children and youth under age 18 living with disabilities is growing and will continue rising in coming decades....
