Where changes in level are permitted in floor or ground surfaces, they shall comply with Section 11B-303. Exceptions: 1. ...
Search Results "Surface Material"
Filters
Commonly Searched Documents
-
11B-303.1 General
-
11B-303.1 General
Where changes in level are permitted in floor or ground surfaces, they shall comply with Section 11B-303. Exceptions: 1. ...
-
SuperDeck Beach Boardwalk
SuperDeck's low-maintenance decking provides a firm, secure beach boardwalk surface over virtually any terrain....
-
902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground....
-
5.2.2 Transfer Surface Size for Equipment Used by Patients in Seated Position
5.2.2 Transfer Surface Size for Equipment Used by Patients in Seated Position....
-
Inpro Corporation JointMaster® 316 Series Single Sightline for Carpet Floor Expansion Joint Covers
The 316 series system was specially designed for continuous flooring types such as carpet and vinyl sheet. Features & Benefits System reduces joint widths of up to 4"...
-
§ 38.83(b)(6) Platform surface
(6) Platform surface. The lift platform surface shall be free of any protrusions over 1/4 inch high and shall be slip resistant....
-
M301.2.3.1 End Transfer Surface
End transfer surfaces shall be 28 inches (710 mm) wide minimum and 17 inches (430 mm) long minimum. ...
-
M301.2.3.2 Side Transfer Surface
Side transfer surfaces shall be 28 inches (710 mm) wide minimum and 28 inches (710 mm) long minimum....
-
Populas Vox Two-Story Adjustable Dual Surface Workstation
Standard Features Adjustment range 24” - 50“ Front surface adjustment range 20” - 57” (4” below, 7” above rear surface), with 15 +/- tilt Power adjusted standard 110V, UL Listed...
-
Pilot Rock TQ700 Square Frame Square Utility Table
Surface mount installation only (Anchor bolts not included - use Model ANC3-4 Anchor Kit). FINISH: All steel frame components have a powder coat finish in your choice of color....
-
Pilot Rock T700 Square Frame Rectangular Utility Table
Surface mount installation only (Anchor bolts not included - use Model ANC3-4 Anchor Kit). FINISH: All steel frame components have a powder coat finish in your choice of color....
-
GAP ARMOUR
GAP ARMOUR IS AN INNOVATIVE RUBBER MATERIAL ...that easily installs (with a rubber hammer) into open concrete expansion joints to completely seal and protect!...
-
11B-503.4 Floor and ground surfaces
Vehicle pull-up spaces and access aisles serving them shall comply with Section 11B-302. Access aisles shall be at the same level as the vehicle pull-up space they serve. Changes in...
-
11B-503.4 Floor and ground surfaces
Vehicle pull-up spaces and access aisles serving them shall comply with Section 11B-302. Access aisles shall be at the same level as the vehicle pull-up space they serve. Changes in...
-
11B-812.3 Floor or ground surfaces
Vehicle spaces and access aisles serving them shall comply with Section 11B-302. Access aisles shall be at the same level as the vehicle space they serve. Changes in level, slopes...
-
11B-812.3 Floor or ground surfaces
Vehicle spaces and access aisles serving them shall comply with Section 11B-302. Access aisles shall be at the same level as the vehicle space they serve. Changes in level, slopes...
-
3. Study Findings
[See subsections ...]
-
Components of Accessible Routes
[See subsections ...]
-
Ytterberg Scientific Inc. FloorPro® Floor Flatness Measurement Device
It's Easier to Use, Gets Faster Results, and Produces Superior Reporting on More ASTM Specifications. FloorPro® Gives You Immediate Results, Instant F-Numbers, Waviness Index,...
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
§ 38.159(b)(6) Platform surface
(6) Platform surface. The platform surface shall be free of any protrusions of 1/4 inch (6.5 mm) high and shall be slip resistant....
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
