14) Carpet and carpet tile ADAAG: Same standards for carpet and carpet tile: maximum pile height of 1/2" (§4.5.3). UFAS: Carpet must have maximum pile height of 1/2". Carpet...
Search Results "Work Surface"
Filters
Commonly Searched Documents
-
14) Carpet and carpet tile
-
Why a smooth surface door or kickplate is important
And those nicks slice your fingers like butter when you least expect it.
-
M303.2.5 Surfaces (Section-by-Section Analysis)
The MDE NPRM proposed to require diagnostic equipment used by patients seated in a wheelchair to provide a wheelchair space with a surface that does not slope more than 1:48 in any direction...
-
Acceptable SEWF Systems
Because of their reactivity, the stabilizing binders needed to be applied on site or mixed with EWF no longer than 1 h prior to placement on the ground surface....
-
4.2.2 Cooking Surface Height
The cooking surface shall be at least 15 inches (380 mm) and no more than 34 inches (865 mm) above the floor or ground surface. ...
-
809.2.1.2 Floor Surfaces
809.2.1.2 Floor Surfaces This section specifies that carpet not be provided on floor surfaces in emergency transportable housing units with mobility features....
-
II. Research Methodology
By 2007 installation of surface materials for testing was begun at Bradford Woods located at Indiana University....
-
III. Results of the Study
Results of the Study The purpose of the longitudinal study was to evaluate a variety of aggregate and organic or natural byproduct soil stabilizer trail surface materials for their ability...
-
Moisture and Durability
these surfacing systems....
-
Exposed Pipes and Surfaces [4.19.4]
Exposed Pipes and Surfaces [4.19.4] To prevent burns, hot water pipes and drain pipes under lavatories must be insulated or otherwise configured to protect against contact....
-
Abstract
Surfaces research project....
-
606.5 Exposed Pipes and Surfaces
606.5 Exposed Pipes and Surfaces. Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact....
-
408.4.2 Floor Surfaces
408.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303....
-
RECOMMENDATIONS
RECOMMENDATIONS An objective test procedure for measuring the firmness and stability of surfaces with a portable device and performance specifications need to be accepted in order to...
-
Aluminum Swaged SG Series Pressure-Locked Grating
Slip resistant & serrated surfaces also available....
-
Unity Surfacing Systems Soft-Land Rubberized Safety Surfacing
Soft-Land is "Unity's" 3", 3 1/4", 3 1/2" and 3 3/4" thick rubberized safety surfacing, flooring and paver products that are made from 100% recycled tires and rubber granules....
-
Aluminum Dove Tail Series Pressure-Locked Grating
Slip resistant & serrated surfaces also available....
-
Data Collection Procedures
study surfaces. ...
-
6. Minimum (Low) Height Standard for Transfer Surfaces
Minimum (Low) Height Standard for Transfer Surfaces As indicated in Section 5.1.1, the MDE Advisory Committee recommends that equipment with transfer surfaces be height adjustable in...
-
FIGURE 11A-10A KITCHEN SPECIFICATIONS
(2) 30" minimum countertop for work surface with removable base cabinet and finish flooring beneath; 30" x 48" minimum clear floor space to allow parallel or forward approach....
-
6. Recognize that Proper Installation of Play Surface Systems is Key
Recognize that Proper Installation of Play Surface Systems is Key An accessible surface system can be rendered useless if it is not properly installed....
-
Stability
The degree to which a surface resists change from contaminants or applied force, so that when the contaminant or force is removed, the surface returns to its original condition (U.S....
-
Firm
A firm surface resists deformation by indentations....
-
Section 4.26.4
• Section 4.26.4 of the 1991 Standards requires handrail gripping surfaces to have edges with a minimum radius of 1/8 inch....
