The seat values are of particular importance because vertical vibrations transferred through the seat of a seated individual are the most hazardous....
Search Results "Vertical Alignment"
Filters
Commonly Searched Documents
-
Engineered vs. Outside
-
4.34.6.8* REFRIGERATOR/FREEZER
Provision shall be made for refrigerators which are: (1) Of the vertical side-by-side refrigerator/freezer type; or (2) Of the over-and-under type and meet the following requirements...
-
11B-1002.4.4 Clearances
Wheelchair spaces shall not be required to comply with Section 11B-307.4 _|Vertical Clearance|_. [2010 ADAS] Advisory 1002.4.4 Clearances Exception 3....
-
11B-303.3 Beveled
A change in level of ½ inch (13 mm) is permitted to be ¼ inch (6.4 mm) vertical plus ¼ inch (6.4 mm) beveled....
-
§ 38.159(b)(8) Platform entrance ramp
loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, measured on level ground, for a maximum rise of 3 inches (75 mm), and the transition from roadway or sidewalk to ramp may be vertical...
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend to points horizontally 30 inches (762 mm), vertically 7 inches (178 mm) and not more than 12 inches (305 mm) from the head and foot end of the bed....
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend to points horizontally 30 inches (762 mm), vertically 7 inches (178 mm) and not more than 12 inches (305 mm) from the head and foot end of the bed....
-
E102.5 IETF (Section-by-Section Analysis)
This proposed standard would be new to the 508 Standards (as well as the 255 Guidelines), and represents a significant shift to better align with current technology....
-
R305.2.1 Perpendicular Curb Ramps
The rows of truncated domes in detectable warning surfaces should be aligned perpendicular to the grade break between the ramp run and the street so pedestrians who use wheelchairs can ”...
-
R305 Detectable Warning Surfaces (Section-by-Section Analysis)
R305 Detectable Warning Surfaces (Section-by-Section Analysis) Detectable warning surfaces consist of truncated domes aligned in a square or radial grid pattern....
-
a. Structural Strength
The MDE NPRM proposed to require transfer supports to be capable of resisting vertical and horizontal forces of 250 pounds at all points (proposed M305.2.2)....
-
Transfer Protocols
The maximum and minimum vertical distances that were attainable were recorded....
-
Section 35.151(g)(4)
least one of the following criteria: (1) It is located within the rear 60 percent of the seats provided in the auditorium; or (2) it is located within the area of the auditorium where the vertical...
-
Section 36.406(f)(4)
least one of the following criteria: (1) It is located within the rear 60 percent of the seats provided in the auditorium; or (2) It is located within the area of the auditorium where the vertical...
-
F206.2.4 Spaces and Elements
Raised courtroom stations, including judges' benches, clerks' stations, bailiffs' stations, deputy clerks' stations, and court reporters' stations shall not be required to provide vertical...
-
206.2.4 Spaces and Elements
Raised courtroom stations, including judges' benches, clerks' stations, bailiffs' stations, deputy clerks' stations, and court reporters' stations shall not be required to provide vertical...
-
206.2.7 Press Boxes
Exceptions 1 – 3 are preempted by Florida vertical accessibility requirements of s. 553.509, F.S., as incorporated in section 201.1.1....
-
222.1 General
Florida vertical accessibility requirements of s.553.509, F.S., as incorporated in section 201.1.1 require vertical access to all levels of rooms....
-
F. Chapter 5: Doorways, Circulation Paths, and Fare Collection Devices
Additionally, in the final rule, the technical requirements for vertical clearances at doorways with lifts or ramps and for illumination at doorway areas have been restated using text in...
-
11B-306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
303.3 Beveled
A change in level of ½ inch (13 mm) is permitted to be ¼ inch (6.4 mm) vertical plus ¼ inch (6.4 mm) beveled....
-
206.3 Location
Additionally, accessible vertical interior circulation must be in the same area as stairs and escalators, not isolated in the back of the facility....
-
306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
11B-404.3.5 Controls
Where push plates, vertical actuation bars or other similar operating devices are provided, they shall be placed in a conspicuous location. ...