Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
Search Results "Ramp Surface"
-
Handrail Gripping Surfaces: ADA Standard Section 1008.2.5.3.1
-
Technical Bulletin: Ground and Floor Surfaces
UNITED STATES ACCESS BOARD A FEDERAL AGENCY COMMITTED TO ACCESSIBLE DESIGN Technical Bulletin: Ground and Floor Surfaces...
-
Door and Gate Surfaces [§404.2.10]
Door and Gate Surfaces [§404.2.10] The bottom surface of doors and gates on the push side must be smooth to a height of at least 10”....
-
11B-404.2.4.4 Floor or ground surface
Floor or ground surface within required maneuvering clearances shall comply with Section 11B-302....
-
1) Where the Standard specifically refers to 303
1) Where the Standard specifically refers to 303, such as 403.4 changes in level for walking surfaces: Here it is clear that changes in level that comply with either the ¼" maximum vertical...
-
Firmness, Stability, and Slip Resistance [§302.1]
Firmness, Stability, and Slip Resistance [§302.1] Accessible floor and ground surfaces must be stable, firm, and slip resistant....
-
Test Courses & Surfaces
Test Courses & Surfaces Test courses were designed and built using nine different types of exterior surfaces (Table 1)....
-
IV. Discussion of Findings and Implications
of surface maintenance to assure accessibility and safety for use by children on a daily basis. ...
-
11B-902.4 Dining surfaces and work surfaces for children’s use
Accessible dining surfaces and work surfaces for children’s use shall comply with Section 11B-902.4....
-
11B-902.4 Dining surfaces and work surfaces for children’s use
Accessible dining surfaces and work surfaces for children’s use shall comply with Section 11B-902.4....
-
11B-902.4 Dining surfaces and work surfaces for children’s use
Accessible dining surfaces and work surfaces for children’s use shall comply with Section 11B-902.4....
-
3. Ground and floor surface treatments
Ground and floor surface treatments 4.5 Accessible routes, and spaces, including floors, walks, ramps, stairs, and curb ramps....
-
§ 36.304(e) Portable ramps
(e) Portable ramps. Portable ramps should be used to comply with this section only when installation of a permanent ramp is not readily achievable....
-
410.2 Floor Surfaces
Floor surfaces in platform lifts shall comply with 302 and 303....
-
410.2 Floor Surfaces
Floor surfaces in platform lifts shall comply with 302 and 303....
-
A4.5.1 General
Soft loose surfaces such as shag carpet, loose sand or gravel, wet clay, and irregular surfaces such as cobblestones can significantly impede wheelchair movement....
-
Legislation
Obstacle Height 1/4" No slope required 1/4"-1/2" Beveled with Maximum 1:2 slope Ramps...
-
R408.4 Tread Surface
R408.4 Tread Surface. Stairway treads shall comply with R302.7. Changes in level are not permitted....
-
Section 35.151(i) Curb Ramps (Section-by-Section Analysis)
The current § 35.151(e) on curb ramps has been redesignated as § 35.151(i). ...
-
General: ADA Standard Section 303.1
Section 303.1 of the ADA Standards covers information in the current ADA Standards for changes in level for floor and ground surfaces.
-
Error/Omission: Parts of an accessible route with slopes that exceed 1:20 lack required features including handrails and edge protection.
Result: When a walkway or other pedestrian surface has a slope greater then 1:20, it is more difficult to maintain control of a wheelchair....
-
Circular Cross Section and Clearance (§505.5, §505.7)
Circular Cross Section and Clearance (§505.5, §505.7)
-
Macro Supa-Trac Heavy Duty Ground Surface
Panel (sq ft/pc): 2.26 Shipping (sq ft): Trailer 53′: 21,969, Trailer 48′: 20,250, Flatbed 48′: 21,969 Static Compression Capacity (lbs/sq ft): 36,000* *Solid sub-surface...
-
609.5 Surface Hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
