Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
Search Results "Expected Maximum Flight Duration"
-
11B-104.1.1 Construction and manufacturing tolerances
-
§ 36.402(c) To the maximum extent feasible.
(c) To the maximum extent feasible....
-
7.2.1 General Exception 1
Where a condition in 7.1 prohibits full compliance with a specific requirement in 7.4 on a trail segment, that trail segment shall comply with the specific requirement to the maximum extent...
-
§ 37.43(b)
(b) As used in this section, the phrase to the maximum extent feasible applies to the occasional case where the nature of an existing facility makes it impossible to comply fully with applicable...
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Exception: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable...
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Exception: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable...
-
F104.1.1 Construction and Manufacturing Tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
104.1.1 Construction and Manufacturing Tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
104.1.1 Construction and Manufacturing Tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
Sec.36.402(c) To the maximum extent feasible
(c) To the maximum extent feasible....
-
308.3.2 Obstructed High Reach
and the depth of the obstruction shall be 24 inches (610 mm) maximum....
-
11B-1002.4.3 Gaps
at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (15.9 mm) and the horizontal gap shall be 3 inches (76 mm) maximum...
-
11B-1002.4.3 Gaps
at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (15.9 mm) and the horizontal gap shall be 3 inches (76 mm) maximum...
-
Figure 308.3.1 Unobstructed Side Reach – Drawing from the U.S. Access Board
-
308.3 Side Reach
308.3 Side Reach
-
11B-308.3 Side reach
[See subsections ...]
-
1015.1 General
Viewing areas shall comply with 1015. EXCEPTION: In alterations, when an entity determines that a condition in 1019 does not permit full compliance with a specific provision in...
-
1014.1 General
Camp shelters shall comply with 1014. EXCEPTIONS: 1. When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1014, the camp...
-
Exceptions [1014.1, Exceptions 1 and 2]
When a condition for exception does not permit full compliance with a specific provision in the technical requirements for camp shelters, the camp shelter must comply with the...
-
308.3 Side Reach
[See subsections ...]
-
308.3 Side Reach
[See subsections ...]
-
1015.1 General
Viewing areas shall comply with 1015. EXCEPTION: In alterations, when an entity determines that a condition in 1019 does not permit full compliance with a specific provision in...
-
1014.1 General
Camp shelters shall comply with 1014. EXCEPTIONS: 1. When an entity determines that a condition in 1019 does not permit full compliance with a specific provision in 1014, the camp...
-
Side Reach Radius
Elements located in corners can be difficult to reach from a side approach. Recommendation: Where a side reach is provided, locate elements away from corners in...
