6”X6”X42” Tall, Clear Anodized Aluminum (628), Surface mount with concealed mounting base, 1 prep for INGRESS’R® ADA switch, Removable Black ABS cap Shown on the bollard- I36-3...
Search Results "Vertical Clearance"
Filters
Commonly Searched Documents
-
Wikk Industries Inc. PART#BPS SM-INGR CLEAR (628) with I36-3 CLEAR (628)
-
5.7.1.2 Lift Compatibility Clearance in Base for Imaging Equipment (M301)
5.7.1.2 Lift Compatibility Clearance in Base for Imaging Equipment (M301) The Committee recommends the use of alternative means of access by an overhead lift in place of clearances in...
-
11B-606.7 Sink depth
Where a forward approach is required at a sink, knee and toe clearance shall be provided in compliance with Section 11B-306....
-
11B-606.7 Sink depth
Where a forward approach is required at a sink, knee and toe clearance shall be provided in compliance with Section 11B-306....
-
M303.2.4.2 Other Equipment
Wheelchair spaces beneath diagnostic equipment other than breast platforms shall comply with M303.2.4.2.
-
2. Accessible lavatory with knee and toe space
2. Accessible lavatory with knee and toe space below, faucet controls usable with a loosely closed fist, clear floor space for front approach, and lowered mirror.
-
11B-809.10.5.1 Clear floor space
lavatory, located at the control end of the tub, shall be permitted to encroach on the clear floor space provided the lavatory is 19 inches (483 mm) maximum in depth, and knee and toe clearance...
-
§ 35.151(g)(4)
(4) Stadium-style movie theaters locate wheelchair seating spaces and companion seating on a riser or cross-aisle in the stadium section that satisfies at least one of the following...
-
4.11.2* Other Requirements
If platform lifts (wheelchair lifts) are used, they shall comply with 4.2.4, 4.5, 4.27, and ASME A17.1 Safety Code for Elevators and Escalators, Section XX, 1990.
-
§ 35.151(g)(4)
(4) Stadium-style movie theaters shall locate wheelchair spaces and companion seats on a riser or cross-aisle in the stadium section that satisfies at least one of the following...
-
11B-606.7 Sink depth
Where a forward approach is required at a sink, knee and toe clearance shall be provided in compliance with Section 11B-306....
-
Voting Area
Within the voting area there must be enough clearance for an individual with a disability to access and use all the voting equipment....
-
Re: 404.2.4.3 Recessed Doors and Gates
Notice that the text does not match the figure for a push approach door. This may be an error in the Standards, but since the text governs, it exceeds the illustrated requirement. ...
-
4.17.5* DOORS
If toilet stall approach is from the latch side of the stall door, clearance between the door side of the stall and any obstruction may be reduced to a minimum of 42 in (1065 mm)....
-
Access Board: Accessible Van Parking
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in it's entirety on the Access Board's website here:...
-
4.17.5* Doors
If toilet stall approach is from the latch side of the stall door, clearance between the door side of the stall and any obstruction may be reduced to a minimum of 42 in (1065 mm) (Fig. 30...
-
11B-404.2.4.1 Swinging doors and gates
TABLE 11B-404.2.4.1 MANEUVERING CLEARANCES AT MANUAL SWINGING DOORS AND GATES TYPE OF USE MINIMUM MANEUVERING CLEARANCE Approach...
-
11B-809.10.4 Sufficient maneuvering space
The clear maneuvering space shall be permitted to include knee and toe clearance under bathroom fixtures....
-
1132A.4 Level floor or landing
1132A.4 Level floor or landing. See also Chapter 10. The floor or landing on each side of a door shall be level. Primary entry doors, required exit doors or secondary exterior doors...
-
8. Gap
8. Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so...
-
11. Gap
11. Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so...
