Elevator car controls shall comply with 407.4.6. Control panels shall be centered on a side wall....
Search Results "Car Ramp"
-
408.4.6 Car Controls
-
408.4.6 Car Controls
Elevator car controls shall comply with 407.4.6. Control panels shall be centered on a side wall....
-
11B-505.2 Where required
Handrails shall be provided on both sides of stairs and ramps. Exceptions: 1. ...
-
11B-505.2 Where required
Handrails shall be provided on both sides of stairs and ramps. Exceptions: 1. ...
-
11B-406 CURB RAMPS, BLENDED TRANSITIONS AND ISLANDS
11B-406 Curb ramps, blended transitions and islands [2010 ADAS] 406 Curb Ramps ETA Editor's Note The differences between 2010 ADAS Section 406 and 2013 CBC Section 11B-406...
-
11B-407.4.6.1 Location
In existing elevators, car control buttons with floor designations shall be permitted to be located 54 inches (1372 mm) maximum above the finish floor when a parallel approach is provided...
-
11B-407.4.6.1 Location
In existing elevators, car control buttons with floor designations shall be permitted to be located 54 inches (1372 mm) maximum above the finish floor when a parallel approach is provided...
-
405.3 Cross Slope
Cross slope of ramp runs shall not be steeper than 1:48. Advisory 405.3 Cross Slope. Cross slope is the slope of the surface perpendicular to the direction of travel....
-
11B-407.4.7.1 Buttons
Car control buttons shall comply with Section 11B-407.4.7.1....
-
11B-407.4.6.2.4 Operation
Car control buttons shall be activated by a mechanical motion that is detectable....
-
11B-407.4.6.2.4 Operation
Car control buttons shall be activated by a mechanical motion that is detectable....
-
11B-407.4.7.1 Buttons
Car control buttons shall comply with Section 11B-407.4.7.1....
-
11B-407.4.7.1 Buttons
Car control buttons shall comply with Section 11B-407.4.7.1....
-
11B-407.4.6.2.4 Operation
Car control buttons shall be activated by a mechanical motion that is detectable....
-
407.4.7.1 Buttons
Car control buttons shall comply with 407.4.7.1....
-
§ 38.83(c)(5) Slope
Ramps or bridge plates shall have the least slope practicable....
-
T402.5 Surfaces
Ramp and bridgeplate surface material shall comply with T302 and extend across the full width and length of the ramp or bridgeplate....
-
§ 37.89 Remanufacture of intercity and commuter rail cars and purchase or lease of remanufactured intercity and commuter rail cars
[See subsections ...]
-
§ 36.304(e) Portable ramps
(e) Portable ramps. Portable ramps should be used to comply with this section only when installation of a permanent ramp is not readily achievable....
-
11B-405.2 Slope
Ramp runs shall have a running slope not steeper than 1:12. Exception: Reserved....
-
11B-405.2 Slope
Ramp runs shall have a running slope not steeper than 1:12. Exception: Reserved....
-
11B-405.2 Slope
Ramp runs shall have a running slope not steeper than 1:12. Exception: Reserved....
-
§ 38.125(b)(7) Platform gaps
When the lift is at car floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and car floor shall not exceed 1/2 inch horizontally...
-
§ 38.95(b)(4) Power or equipment failure
(4) Power or equipment failure. Platforms stowed in a vertical position, and deployed platforms when occupied, shall have provisions to prevent their deploying, falling, or folding...