Amusement ride seats designed for transfer shall comply with Section 11B-1002.5 when positioned for loading and unloading....
Search Results "Comply With"
-
11B-1002.5 Amusement ride seats designed for transfer
-
11B-308.1 General
Reach ranges shall comply with Section 11B-308. Advisory 11B-308.1 General....
-
11B-307.2 Protrusion limits
Elements located on circulation paths, including operable elements, must comply with requirements for protruding objects....
-
11B-707 Automatic teller machines, fare machines and point-of-sale devices
Federal procurement law requires that ITMs purchased by the Federal government comply with standards issued by the Access Board under Section 508 of the Rehabilitation Act of 1973, as amended...
-
11B-806.3 Guest rooms with communication features
Guest rooms required to provide communication features shall comply with Section 11B-806.3. Advisory 11B-806.3 Guest rooms with communication features....
-
11B-407.3.4 Door and signal timing
Destination-oriented elevators shall not be required to comply with 407.3.4....
-
11B-810.2.2 Dimensions
Public entities shall ensure that the construction of bus boarding and alighting areas comply with 810.2.2, to the extent the construction specifications are within their control....
-
11B-809.9.2 Clear width
U-shaped kitchens, with a cooktop, sink or work surface located at the base of the U, that provides knee and toe space complying Sections 11B-809.9.3 and 11B-809.9.4 to allow for a forward...
-
11B-703.4.1 Height above finish floor or ground
Exception: Tactile characters for elevator car controls shall not be required to comply with Section 11B-703.4.1....
-
604.3.2 Overlap
EXCEPTION: In residential dwelling units, a lavatory complying with 606 shall be permitted on the rear wall 18 inches (455 mm) minimum from the water closet centerline where the clearance...
-
704.4.1 Height
EXCEPTION: Where seats are provided, TTYs shall not be required to comply with 704.4.1. Advisory 704.4.1 Height....
-
308.1 General
Reach ranges shall comply with 308. Advisory 308.1 General....
-
704.4.1 Height
EXCEPTION: Where seats are provided, TTYs shall not be required to comply with 704.4.1. Advisory 704.4.1 Height....
-
1002.5 Amusement Ride Seats Designed for Transfer
Amusement ride seats designed for transfer shall comply with 1002.5 when positioned for loading and unloading. Advisory 1002.5 Amusement Ride Seats Designed for Transfer....
-
308.1 General
Reach ranges shall comply with 308. Advisory 308.1 General....
-
806.3 Guest Rooms with Communication Features
Guest rooms required to provide communication features shall comply with 806.3. Advisory 806.3 Guest Rooms with Communication Features....
-
407.3.4 Door and Signal Timing
Destination-oriented elevators shall not be required to comply with 407.3.4....
-
1002.4.3 Gaps
EXCEPTION: Where compliance is not operationally or structurally feasible, ramps, bridge plates, or similar devices complying with the applicable requirements of 36 CFR 1192.83(c) shall...
-
307.2 Protrusion Limits
Elements located on circulation paths, including operable elements, must comply with requirements for protruding objects....
-
1004.1 Clear Floor Space
Exercise machines and equipment shall have a clear floor space complying with 305 positioned for transfer or for use by an individual seated in a wheelchair....
-
604.7 Dispensers
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
610.3 Shower Compartment Seats
Seats shall comply with 610.3.1 or 610.3.2....
-
11B-208.2 Minimum number
Parking spaces complying with Section 11B-502 shall be provided in accordance with Table 11B-208.2 except as required by Sections 11B-208.2.1, 11B-208.2.2, and 11B-208.2.3....
-
7.11(a) Collective Bargaining Agreements
7.11(a)Collective Bargaining Agreements Labor unions are covered by the ADA and have the same obligation as the employer to comply with its requirements....