Currently, the regulation provides that alterations to historic facilities shall comply to the maximum extent feasible with section 4.1.7 of UFAS or section 4.1.7 of the 1991 Standards....
Search Results "Comply With"
-
Section 35.151(b)(3) Alterations to historic facilities
-
"Housing at a place of education" definition
a year-round basis exclusively to graduate students or faculty, and do not contain any public use or common use areas available for educational programming; instead, such housing shall comply...
-
11B-1002.5 Amusement ride seats designed for transfer
Amusement ride seats designed for transfer shall comply with Section 11B-1002.5 when positioned for loading and unloading....
-
704.4.1 Height
EXCEPTION: Where seats are provided, TTYs shall not be required to comply with 704.4.1. Advisory 704.4.1 Height....
-
Aisle Seats
Complying armrests are not required where no armrests are provided on seats....
-
6. Maintenance and Back-up of TTY Equipment
The ADA regulation contains a specific provision requiring that covered entities maintain their accessible features and equipment in operable working condition.4 To comply with this regulation...
-
11B-707 AUTOMATIC TELLER MACHINES, FARE MACHINES AND POINT-OF-SALE DEVICES
Federal procurement law requires that ITMs purchased by the Federal government comply with standards issued by the Access Board under Section 508 of the Rehabilitation Act of 1973, as amended...
-
11B-806.3 Guest rooms with communication features
Guest rooms required to provide communication features shall comply with Section 11B-806.3. [2010 ADAS] Advisory 806.3 Guest Rooms with Communication Features. ...
-
11B-225.2.3 Library book stacks
Book stacks restricted to employee use are not required to comply with these requirements....
-
1004.1 Clear Floor Space
Exercise machines and equipment shall have a clear floor space complying with 305 positioned for transfer or for use by an individual seated in a wheelchair....
-
1002.5 Amusement Ride Seats Designed for Transfer
Amusement ride seats designed for transfer shall comply with 1002.5 when positioned for loading and unloading. Advisory 1002.5 Amusement Ride Seats Designed for Transfer....
-
Sloped Entries
Sloped Entries Sloped entries must comply with ADAAG accessible route provisions (36 inch minimum width, maximum 1:12 or 8.33% slope), except that the surface does not need to be slip...
-
604.3.2 Overlap
EXCEPTION: In residential dwelling units, a lavatory complying with 606 shall be permitted on the rear wall 18 inches (455 mm) minimum from the water closet centerline where the clearance...
-
703.3.1 Dimensions and Capitalization
Braille dots shall have a domed or rounded shape and shall comply with Table 703.3.1....
-
308.1 General
Reach ranges shall comply with 308. Advisory 308.1 General....
-
407.3.4 Door and Signal Timing
Destination-oriented elevators shall not be required to comply with 407.3.4....
-
407.3.4 Door and Signal Timing
Destination-oriented elevators shall not be required to comply with 407.3.4....
-
604.7 Dispensers
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
Driving Ranges
Driving Ranges Both stand-alone driving ranges and driving ranges adjacent to a golf course that provide teeing stations or practice teeing grounds must comply with the following:...
-
704.4.1 Height
EXCEPTION: Where seats are provided, TTYs shall not be required to comply with 704.4.1. Advisory 704.4.1 Height....
-
Specific Remedial Measures
The Museum agrees to comply with the ADA and to ensure that the content of its exhibitions, public programs, and other offerings are accessible and effectively communicated to individuals...
-
610.3 Shower Compartment Seats
Seats shall comply with 610.3.1 or 610.3.2....
-
308.1 General
Reach ranges shall comply with 308. Advisory 308.1 General....
-
5.1.4 Transfer Surface Height Measurement for M301 and M302
Identifying the highest point on the transfer surface will assure that all points on the transfer surface comply with the height criteria....