All operable parts, including coin slots, shall be 40 inches (1016 mm) maximum above the finish floor....
Search Results "Clear Floor Area"
-
11B-603.5 Accessories
-
407.12.3.1 Unobstructed Forward Reach (Section-by-Section Analysis)
Analysis) This section proposes that, where an unobstructed forward reach is provided, the operable part must be located 48 inches high maximum and 15 inches high minimum above the floor...
-
407.12.2.2 Obstructed Side Reach (Section-by-Section Analysis)
located more than 10 inches, but not more than 24 inches, behind the vertical reference plane, the height of the operable part must be 46 inches maximum and 15 inches minimum above the floor...
-
4.10.6* Door Protective and Reopening Device
device shall be capable of completing these operations without requiring contact for an obstruction passing through the opening at heights of 5 in and 29 in (125 mm and 735 mm) above finish floor...
-
4.10.3 Hall Call Buttons
Call buttons in elevator lobbies and halls shall be centered at 42 in (1065 mm) above the floor....
-
4.13.9* Door Hardware
Hardware required for accessible door passage shall be mounted no higher than 48 in (1220 mm) above finished floor....
-
4.10.3 HALL CALL BUTTONS
Call buttons in elevator lobbies and halls shall be centered at 42 in (1065 mm) above the floor....
-
Slope [4.3.7]
Requirements in 4.3, while based on the expectation of level floors, apply equally to exterior sites....
-
4.30.6 Mounting Location and Height
Mounting height shall be 60 in (1525 mm) above the finish floor to the centerline of the sign....
-
4.10.6* DOOR PROTECTIVE AND REOPENING DEVICE
device shall be capable of completing these operations without requiring contact for an obstruction passing through the opening at heights of 5 in and 29 in (125 mm and 735 mm) from the floor...
-
11B-604.9.6 Dispensers
The outlet of the dispenser shall be 14 inches (356 mm) minimum and 19 inches (483 mm) maximum above the finish floor....
-
610.2 Bathtub Seats
The top of bathtub seats shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the bathroom finish floor....
-
Proline Drain
We also offer a variety of spacers to raise the linear drain cover to the height of your floor....
-
§ 36.403(a)(2)
1991 Standards, the private entity is not required to retrofit such elements to reflect the incremental changes in the 2010 Standards solely because of an alteration to a primary function area...
-
11B-707.6.1 Input controls
Where provided, key surfaces not on active areas of display screens, shall be raised above surrounding surfaces....
-
707.6.1 Input Controls
Where provided, key surfaces not on active areas of display screens, shall be raised above surrounding surfaces....
-
802.1.2 Width
[ECTCR UFAS 4.33.2, Fig. 46] Figure 802.1.2 Width of Wheelchair Spaces in Assembly Areas...
-
§ 36.403(a)(1)
1991 Standards, the private entity is not required to retrofit such elements to reflect incremental changes in the proposed standards solely because of an alteration to a primary function area...
-
9.2.2(2)
This is not intended to require an elevator in multi-story units as long as the spaces identified in 9.2.2(6) and (7) are on accessible levels and the accessible sleeping area is suitable...
-
10.3.2(1)
by the Department of Transportation in subpart C of 49 CFR part 37 and existing intercity rail stations shall provide at least one accessible route from an accessible entrance to those areas...
-
4.7.11 Islands
Any raised islands in crossings shall be cut through level with the street or have curb ramps at both sides and a level area at least 48 in (1220 mm) long between the curb ramps in the part...
-
E2-3. Interior Stairs
., protected with a cane-detectable warning or a barrier that prevents travel into the area with less than an 80-inch-high head clearance)? [ADA Stds 4.4.2] Yes _____ No _____...
-
§100.143(b)(2)
(2) Assess the extent and scope of any likely violation, by determining which areas of operation are likely to be affected by those policies and practices, such as stages of the loan application...
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
