In the proposed rule, the reference to rehabilitation and physical outpatient therapy facilities covered in 208.2.2 was inadvertently omitted....
Search Results "Vertical Reference Plane"
-
Requirement for Van Spaces in All Types of Facilities
-
404.3 Automatic and Power-Assisted Doors and Gates
Full-powered automatic doors shall comply with ANSI/BHMA A156.10 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
404.3 Automatic and Power-Assisted Doors and Gates
Full-powered automatic doors shall comply with ANSI/BHMA A156.10 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
Paratransit
Part 37 uses this term to refer to the complementary paratransit service comparable to public fixed route systems which must be provided....
-
B7-b
[ADA Standards § 4.7.2] Yes No Note: 1:12 is one inch of vertical height for each 12 inches of length....
-
1132A.4.1, Item 2
Thresholds with a change in height between ¼ inch (6.35 mm) and ¾ inch (19.05 mm) shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
‘‘1991 Standards’’ and ‘‘2004 ADAAG’’ (Section-by-Section Analysis)
The term ‘‘1991 Standards’’ refers to the ADA Standards for Accessible Design, originally published on July 26, 1991, and republished as Appendix D to part 36....
-
Landscape Forms Inc. Petoskey Bench Collection
Refer to materials/colors link on this page to view standard selections. FSC® certified woods available....
-
PLATFORM (WHEELCHAIR) LIFT
mechanism equipped with a car or platform or support that serves two landings of a building or structure and is designed to carry a passenger or passengers and (or) luggage or other material a vertical...
-
B. Accessible Route
Is there a route to these 5% accessible fixed tables that allows at least 36" clear width and has no abrupt vertical level changes greater than 1/4"?...
-
e-ii
[ADA Standards § 4.7.2] Yes No Note: 1:12 is one inch of vertical height for 12 inches of horizontal distance....
-
610.4 Structural Strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
903.6 Structural Strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers....
-
1118B.3
Changes in level up to 1/4 inch (6.4 mm) may be vertical and without edge treatment [see Figure 11B-5E(c)]....
-
IV. SPECIFIC RELIEF
References to “Standards” in this Agreement refer to the 2010 ADA Standards for Accessible Design (“Standards”)....
-
Standing Supports [M305.2]
Standing Supports [M305.2] Recommendation: The final recommendation of the subcommittee is to remove the requirement for standing supports in reference to mammography equipment....
-
General: ADA Standard Section 207.1
Section 207.1 of the ADA Standards covers information on scoping requirements for accessible means of egress in the most current ADA Standards.
-
Resources for Air Travelers with Disabilities
The following publications are useful for air travelers with disabilities: Plane Talk – Passengers with Disabilities, Fly Rights, and New Horizons: Information for the Air Traveler with...
-
[2010 ADAS] 105.1 General
The standards listed in 105.2 are incorporated by reference in this document and are part of the requirements to the prescribed extent of each such reference....
-
F105.1 General
The standards listed in F105.2 are incorporated by reference in this document and are part of the requirements to the prescribed extent of each such reference....
-
105.1 General
The standards listed in 105.2 are incorporated by reference in this document and are part of the requirements to the prescribed extent of each such reference....
-
"1991 Standards" and "2004 ADAAG" (Section-by-Section Analysis)
The term ‘‘1991 Standards'' refers to the ADA Standards for Accessible Design, originally published on July 26, 1991, and republished as Appendix D to 28 CFR part 36....
-
[2010 ADAS] 105.1 General
The standards listed in 105.2 are incorporated by reference in this document and are part of the requirements to the prescribed extent of each such reference....
