Comments advised that the guidelines should not address "water coolers," a term which is often used to refer to bottled units that are not plumbed or permanently fixed. Response....
Search Results "Vertical Reference Plane"
Filters
Commonly Searched Documents
-
Drinking Fountains and Water Coolers
-
Requirement for Van Spaces in All Types of Facilities
In the proposed rule, the reference to rehabilitation and physical outpatient therapy facilities covered in 208.2.2 was inadvertently omitted....
-
404.3 Automatic and Power-Assisted Doors and Gates
Full-powered automatic doors shall comply with ANSI/BHMA A156.10 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
404.3 Automatic and Power-Assisted Doors and Gates
Full-powered automatic doors shall comply with ANSI/BHMA A156.10 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
Paratransit
Part 37 uses this term to refer to the complementary paratransit service comparable to public fixed route systems which must be provided....
-
Platform and Vehicle Floor Coordination: ADA Standard Section 810.5.3
In light rail, commuter rail, and intercity rail systems where it is not operationally or structurally feasible to meet the horizontal gap or vertical difference requirements of part 1192...
-
‘‘1991 Standards’’ and ‘‘2004 ADAAG’’ (Section-by-Section Analysis)
The term ‘‘1991 Standards’’ refers to the ADA Standards for Accessible Design, originally published on July 26, 1991, and republished as Appendix D to part 36....
-
11B-903.6 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
303 Changes in Level
Section 303 addresses vertical changes in level in floor or ground surfaces. No changes have been made to this section....
-
11B-609.8 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the grab bar, fastener, mounting device,...
-
11B-903.6 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
11B-307.4.1 Guy braces
Where a guy support is used within either the width of a circulation path or 24 inches maximum outside of a circulation path, a vertical guy brace, sidewalk guy or similar device shall be...
-
11B-307.4.1 Guy braces
Where a guy support is used within either the width of a circulation path or 24 inches maximum outside of a circulation path, a vertical guy brace, sidewalk guy or similar device shall be...
-
Protrusion Limits: ADA Standard Section 307.2
Section 307.2 covers the current ADA Standards for protrusion limits.
-
Gaps: ADA Standard Section 1002.4.3
Floors of amusement rides with wheelchair spaces and floors of load and unload areas shall be coordinated so that, when amusement rides are at rest in the load and unload position, the vertical...
-
11B-307.2 Protrusion limits
For example, awnings and their supporting structures cannot reduce the minimum required vertical clearance....
-
General: ADA Standard Section 207.1
Section 207.1 of the ADA Standards covers information on scoping requirements for accessible means of egress in the most current ADA Standards.
-
5.4.11 Transfer Support Structural Strength Recommendations for M301 and M302
5.4.11 Transfer Support Structural Strength Recommendations for M301 and M302 Description: Transfer supports and their connections must be capable of resisting sufficient vertical and...
-
IV. SPECIFIC RELIEF
References to “Standards” in this Agreement refer to the 2010 ADA Standards for Accessible Design (“Standards”)....
-
MEANS OF EGRESS
A continuous and unobstructed path of vertical and horizontal egress travel from any occupied portion of a building or structure to a public way....
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers. ...
-
Automatic Operation [4.10.2]
Self-leveling must correct the overtravel or undertravel of a car as it stops at a landing within a ½ inch vertical tolerance since changes in level greater than ½ inch can be troublesome...
-
[2010 ADAS] 105.1 General
The standards listed in 105.2 are incorporated by reference in this document and are part of the requirements to the prescribed extent of each such reference....
-
F105.1 General
The standards listed in F105.2 are incorporated by reference in this document and are part of the requirements to the prescribed extent of each such reference....