Vertical alignment may be accomplished by vehicle air suspension, automatic ramps or lifts, or any combination....
Search Results "Vertical Plane"
-
§ 38.73(d)(1) Requirements
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
4.2 Stretchers
First, to serve these multiple purposes, the current configuration of stretchers must accommodate the vertical height needs of numerous components, including (Figure 3.1): the basic elements...
-
Corbin Russwin Inc. ED7000 Series Narrow Stile Crossbar Exit Device
The ED7000 Series are available as Rim, Surface Vertical Rod, Mortise and Concealed Vertical Rod devices. ...
-
PDQ 4200 Series Exit Device Door Hardware
The American Eagle 4200 Series is a rim or surface vertical rod exit device....
-
Husky 24" Line Generator Digital Laser Level
This level may use indoors or out for horizontal (level), vertical (plumb) and square alignment projects....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”. ...
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
A7. Curb Ramps
[ADA Stds 4.7.2] Note: 1:12 is one inch of vertical height for each 12 inches in length. Yes _____ No _____...
-
4.5.2 Changes in Level
Changes in level up to 1/4 in (6 mm) may be vertical and without edge treatment (see Fig. 7(c))....
-
4.5.2 CHANGES IN LEVEL
Changes in level up to 1/4 in (6 mm) may be vertical and without edge treatment (see Fig. 7(c))....
-
Handrails [§504.6, §505]
A vertical clearance 9” minimum between upper and lower handrails will help prevent entrapment....
-
Where Required: Multi-Story Buildings and Facilities [§206.2.3]
provisions in the Standards still apply to stories and mezzanines not served by an accessible route elevators provided anyway must fully comply (as standard or LULA elevators) vertical...
-
§ 38.23(b)(8) Platform entrance ramp
loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, measured on level ground, for a maximum rise of 3 inches, and the transition from roadway or sidewalk to ramp may be vertical...
-
Stanley QRM 100 Series Grade 1 Extra Heavy Duty Exit Devices
In addition, all exit devices are offered in rim, rim fire, surface vertical rod, surface vertical rod fire and surface vertical-less bottom rod configurations....
-
Location: ADA Standard Section 206.3
Section 206.3 covers scoping requirements in the most current ADA Standards for the required locations of accessible routes.
-
Clearances
The 80-inch minimum vertical clearance requirement remains for circulation areas and accessible routes in the queue line and load and unload areas....
-
§ 38.113(d)(1) Requirements
Vertical alignment may be accomplished by car air suspension, platform lifts or other devices, or any combination....
-
§ 38.83(b)(8) Platform entrance ramp
barrier used as a ramp, shall not exceed a slope of 1:8 measured on level ground, for a maximum rise of 3 inches, and the transition from the station platform or roadway to ramp may be vertical...
-
§ 38.95(b)(8) Platform entrance ramp
loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, when measured on level ground, for a maximum rise of 3 inches, and the transition from station platform to ramp may be vertical...
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
Detecto 6550 Portable Wheelchair Scale Operation
The 6550's unique vertical fold-up design allows it to be portable, so it may be wheeled to various locations in a clinical facility....
-
Allegion Von Duprin 22 Series Exit Devices
Von Duprin 22 Series Exit Devices offer: 22 Rim Exit Device & Standard Trim 22-F Rim Fire Exit Device & Standard Trim 2227 Surface Mounted Vertical Rod Device & Trim...
-
Smooth Surface
This provision requires that parts creating joints in the smooth surface are to be within 1/16 inch of the same plane as the other....
