The vertical reference plane shall be centered on the operable part and placed at the leading edge of the maximum protrusion of the ICT within the length of the vertical reference plane....
Search Results "IDeA Center"
Commonly Searched Documents
-
407.12.2 Side Reach
-
A4.13.9 DOOR HARDWARE
To be effective, they should cover the door width, less approximately 2 in (51 mm), up to a height of 16 in (405 mm) form its bottom edge and be centered across the top....
- disABILITY Resource Center (DRC) - Demorest, Gainesville, GA
- Center for Independence - Grand Junction, Carbondale, Montrose, CO
-
III. Enforcement and Implementation
If the United States believes that any of the XL Center Parties has failed to comply in a timely manner with any requirement of this Agreement without obtaining sufficient advance...
-
APPENDIX RESOURCES FOR LOCATING REASONABLE ACCOMMODATIONS
Equal Employment Opportunity Commission 1-800-669-3362 (Voice) 1-800-800-3302 (TT) The EEOC's Publication Center has many free documents on the Title I employment provisions of the...
-
D. Examples of Schools to Which These Guidelines Apply
Note: Subsequent sections of these Guidelines may use the term secondary vocational education center in referring to the institutions described in paragraphs 3, 4 and 5 above or the term...
- Independent Living Center of Kern County - Bakersfield, CA
- disABILITY Resource Center (dRC) - Knoxville, TN
- North Country Center for Independence (NCCI) - Plattsburgh, NY
-
General: ADA Standard Section 233.1
Section 233 of the ADA Standards covers information in the current ADA Standards on scoping requirements for residential facilities.
-
III. FACILITIES COVERED BY THIS CONSENT DECREE
registration desk, the lobby, the public telephones, the public and employee restrooms, the elevators, the units, sleeping rooms and suites, the parking garages, restaurants, bars, spa, fitness center...
-
12.1 Q...How is the individual building test performed for additional stories, to determine if those stories must also be treated as ground floors?
determining whether a non-elevator building has more than one ground floor, the point of measurement for additional ground floors, after the first ground floor has been established, is at the center...
-
7(2)(b)(iv)
In locations where toilets are adjacent to walls or bathtubs, the center line of the fixture is a minimum of 1'6" from the obstacle....
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
-
12183(b) Elevator
be construed to require the installation of an elevator for facilities that are less than three stories or have less than 3,000 square feet per story unless the building is a shopping center...
-
1134A.8, Item 4.3
The knee and toe space shall be centered on the fixture, and shall comply with Section 1138A.2....
-
A4.13.9 Door Hardware
To be effective, they should cover the door width, less approximately 2 in (51 mm), up to a height of 16 in (405 mm) from its bottom edge and be centered across the width of the door....
-
Side Approach
Recommendation: The clear floor space should be centered on the ATM unit....
-
1134A.8, Item 4.3
The knee and toe space shall be centered on the fixture, and shall comply with Section 1138A.2....
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-809.2.2 Turning space
For example, in kitchens, Section 11B-804.3.1 requires at least one work surface with clear floor space complying with Section 11B-306 to be centered beneath....
- National Aging and Disability Transportation Center (NADTC)
- VisionConnect™ Mobile App