“While many people tend to think that the only factor in hearing loss is loudness, there are actually two factors involved: loudness and clarity. ...
Search Results "Two-Way Communication System"
Filters
Commonly Searched Documents
-
2. Numbers of Individuals with Hearing and Vision Disabilities
-
Section 36.406(d) Social Service Center Establishments
The NPRM explained that this proposal was based on two important changes in the 2004 ADAAG....
-
Section 36.406(d) Social Service Center Establishments (Section-by-Section Analysis)
The NPRM explained that this proposal was based on two important changes in the 2004 ADAAG....
-
3.2 Study Limitations and Other Issues
A particularly striking example of these changes has been related by Kirk: [The detectable warning product] exhibited considerable fading over the two-year period.......
-
Appendix 2: Survey Forms: Curb Ramps
If yes, answer one of the next two questions. If not, skip to question 10....
-
Water Closet Clearance
Other commenters urged the Department not to adopt section 604.3 of the 2010 Standards claiming that it will require single-user toilet rooms to be two feet wider than the 1991 Standards...
-
1.7 Procedure
Two “blank” trials were also inserted for each of the sidewalks (except the brick sidewalk) for a grand total of 58 trials....
-
B. The 2010 Standards Regarding Public Entrances Are Intended To Achieve the Same Result As the 1991 Standards Regarding Public Entrances
The two types of entrances at issue here provide a very different experience to customers with and without disabilities. ...
-
E202 General Exceptions (Section-by-Section Analysis)
The Board is proposing to exclude from this rule two exceptions that are contained in the existing 508 Standards: §§ 1194.3(c) and 1194.3(d)....
-
1. Job-Related
There are two job applicants. One has a disability that makes typing very difficult, the other has no disability and can type....
-
Section 1630.2(j)(1)(ix) Effects of an Impairment Lasting Fewer Than Six Months Can Be Substantially Limiting
See Joint Hoyer-Sensenbrenner Statement at 3 (“[T]here is no need for the transitory and minor exception under the first two prongs because it is clear from the statute and the legislative...
-
What is a “reasonable accommodation”?
For example: An accountant with HIV who had no available sick leave required two hours off, monthly, for visits to his doctor....
-
11B-221.3 Companion seats
Where two wheelchair spaces are provided adjacent to one another, one can be used as a companion seat....
-
M305.3 Standing Supports (Section-by-Section Analysis)
Two commenters responded to question 40 (one medical association and a state agency concerned with accessibility), and both concurred that diagnostic equipment could provide a 1½ inch minimum...
-
Notes
., about the two low options for transfer surface height) reflects the Advisory Committee’s activities and thinking at the time of the request to the clinician speakers....
-
2010 ADA Standards
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
104.1.1 Construction and Manufacturing Tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
Fire Rings, Grills, Fireplaces, and Woodstoves [1011.2, 1011.3, and 1011.5]
Fire rings that are constructed with two concentric walls reduce the chances that people using mobility devices and children will receive burns when the outside wall is touched....
-
Participants
Further details of the demographics from the two studies can be seen in Table D1, including hours using a wheelchair per day, years using a wheelchair and number of level and non-level transfers...
-
Web / HTML implementation
The example above shows the result of listing images with the WAT-C toolbar, revealing two errors....
-
Addendum A: List of Terms
Two Step Transfer: a transfer from a wheelchair to a transfer surface (step 1) and then a second transfer to another transfer surface that is either higher or lower than the previous one...
-
104.1.1 Construction and Manufacturing Tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
Sample Documents
The long sample includes timeframes and a two-step process that allows for appeals. The short sample is simpler and more appropriate for small public entities....
-
D. Election Day Compliance Review
If the City does not properly implement the temporary remedial measures necessary at a particular polling place location on Election Day in two (2) consecutive elections, and the City does...