Dining surfaces and work surfaces shall comply with Sections 11B-902.2 and 11B-902.3....
Search Results "Gripping Surface"
Filters
Commonly Searched Documents
-
11B-902.1 General
-
11B-902.1 General
Dining surfaces and work surfaces shall comply with Sections 11B-902.2 and 11B-902.3....
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
Tile Tech Pavers® Oceanic™ Series - Wave-Pave™
pavers can also be manufactured with various design mixes such as crushed seashells, granite chips and recycled glass which are then honed and shot blasted for a unique and slip resistant surface...
-
902.3 Baby Changing Table Work Surface Height
-
Macro Supa-Trac Rigid Ground Cover
Requires the Premium User plan or above. (Login or upgrade your account!) -
Resting Intervals [1018.8]
When the surface of the resting interval is constructed of asphalt, concrete, or boards, the slope of the resting interval must be no steeper than 1:48 (2 percent) in any direction....
-
Cross Section of Gripping Surfaces
The Access Board is considering whether the above cross section dimensions would be appropriate for the gripping surfaces of transfer supports on diagnostic equipment used by patients in...
-
Installation
Installation Surface materials/systems were installed by both contractors and the playground owners’ maintenance staff. ...
-
5.2.2 Transfer Surface Size Recommendations for M302
5.2.2 Transfer Surface Size Recommendations for M302 Description: The transfer surface is the part of the diagnostic equipment onto which patients who use mobility devices or aids transfer...
-
(1) Transfer Surface Location for Diagnostic Equipment Used in the Supine, Prone, or Side-lying Position
its depth spanned the examination surface’s width, and was located near the center point of the diagnostic equipment surface....
-
7. Commit to Ongoing Maintenance of Accessible Playground Surfaces as a Responsibility of Ownership
surfaces....
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE. ...
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
6. Transfer Surface Height
Transfer Surface Height 6.3 Diagnostic Imaging Equipment Refer to the Rationale found in Section 5.3 for M301.2.1 and to Section 4.3....
-
Data Collection Procedures
study surfaces. ...
-
Study Questions
Study Questions The purpose of this study was to evaluate a variety of playground surfaces, their ability to meet accessibility requirement, their costs upon initial installation and...
-
405.9.1 Extended Floor or Ground Surface
405.9.1 Extended Floor or Ground Surface....
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
5.2.2.2 Transfer Surface Depth Recommendation for M302
5.2.2.2 Transfer Surface Depth Recommendation for M302 The Committee recommends a minimum depth requirement of 17 inches for equipment used by patients in seated positions....
-
405.9.1 Extended Floor or Ground Surface
The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505....
-
Inpro Corporation JointMaster® 925 Fire Barrier System Expansion Joint Systems
The 925 Fire Barrier system meets the “Hose System Test” for masonry and concrete walls. Features & Benefits Economical system for joint widths up to 3"...
