Launch Ramps Without Boarding Piers There are no specific provisions that address access to launch ramps without boarding piers....
Search Results "Built-Up Curb Ramp"
Filters
Commonly Searched Documents
-
Launch Ramps Without Boarding Piers
-
11B-707.3 Operable parts
Exception: Drive-up only automatic teller machines and fare machines shall not be required to comply with Sections 11B-309.2 and 11B-309.3....
-
Figure 405.9.1 Extended Floor or Ground Surface Edge Protection – Drawing from the U.S. Access Board
-
11B-502.7.2 Wheel stops
A curb or wheel stop shall be provided if required to prevent encroachment of vehicles over the required clear width of adjacent accessible routes....
-
11B-502.7.2 Wheel stops
A curb or wheel stop shall be provided if required to prevent encroachment of vehicles over the required clear width of adjacent accessible routes....
-
11B-502.7.2 Wheel stops
A curb or wheel stop shall be provided if required to prevent encroachment of vehicles over the required clear width of adjacent accessible routes....
-
Typical Issues
When an accessible route crosses a curb, a curb ramp must be provided....
-
Section C: Exterior Route
(§307.4) C8 If the route crosses a curb, is there a curb ramp that is at least 36" wide with a slope no more than 1:12?...
-
Height: ADA Standard Section 902.4.2
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish floor or ground.
-
Height: ADA Standard Section 902.3
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground.
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground.
-
Scoping [4.1.3(12)]
Scoping [4.1.3(12)] ADAAG covers fixed or built-in storage facilities in public or common use spaces and requires access to at least one of "each type."...
-
A. Question 1: Applicability of Section 904.4.1’s Exception
If, however, Defendants’ transaction counter is equal to or longer than 36 inches as built, Defendants still have complied with 904.4.1 for the reasons explained below.2 2 The submissions...
-
1.2.5 Ramps
1.2.5 Ramps. When overall running slope and cross slope for accessible ramps are measured according to Sections 1.1.11 a recommended tolerance for these slopes is +0.5%....
-
11B-405.9 Edge protection
Edge protection complying with Section 11B-405.9.2 shall be provided on each side of ramp runs and at each side of ramp landings. [2010 ADAS] 405.9 Edge Protection. ...
-
11B-405.9 Edge protection
Edge protection complying with Section 11B-405.9.2 shall be provided on each side of ramp runs and at each side of ramp landings. [2010 ADAS] 405.9 Edge Protection....
-
11B-405.9 Edge protection
Edge protection complying with Section 11B-405.9.2 shall be provided on each side of ramp runs and at each side of ramp landings. [2010 ADA Standards] 405.9 Edge Protection....
-
6f. Ramp Handrails
Are the handrails mounted between 34 and 38 inches above the ramp surface? [ADA Stds 4.8.5] Yes _____ No _____...
-
11B-707.3 Operable parts
Exceptions: Drive-up only automatic teller machines and fare machines shall not be required to comply with Sections 11B-309.2 and 11B-309.3....
-
405.9 Edge Protection
Edge protection complying with 405.9.1 or 405.9.2 shall be provided on each side of ramp runs and at each side of ramp landings. EXCEPTIONS: 1....
-
405.9 Edge Protection
Edge protection complying with 405.9.1 or 405.9.2 shall be provided on each side of ramp runs and at each side of ramp landings. EXCEPTIONS: 1....
-
405.9 Edge Protection
Edge protection complying with 405.9.1 or 405.9.2 shall be provided on each side of ramp runs and at each side of ramp landings. EXCEPTIONS: 1....
-
220 Automatic Teller Machines and Fare Machines
EXCEPTION: Drive-up-only automated teller machines are not required to comply with 4.27.2, 4.27.3 and 4.34.3. 220.1 General....
