Accessibility also includes the appropriate designation and location of spaces and passenger loading zones, their connection to an accessible route, and vertical clearance for vans....
Search Results "Vertical Rod"
Filters
Commonly Searched Documents
-
Parking and Passenger Loading Zones [4.6]
-
Spout Location [4.15.3]
The trajectory of water flow must be vertically "parallel" or "nearly parallel" to the face of the unit....
-
§ 38.73(d)(1) Requirements
Vertical alignment may be accomplished by vehicle air suspension, automatic ramps or lifts, or any combination....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”. ...
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
A7. Curb Ramps
[ADA Stds 4.7.2] Note: 1:12 is one inch of vertical height for each 12 inches in length. Yes _____ No _____...
-
4.5.2 Changes in Level
Changes in level up to 1/4 in (6 mm) may be vertical and without edge treatment (see Fig. 7(c))....
-
4.5.2 CHANGES IN LEVEL
Changes in level up to 1/4 in (6 mm) may be vertical and without edge treatment (see Fig. 7(c))....
-
Handrails [§504.6, §505]
A vertical clearance 9” minimum between upper and lower handrails will help prevent entrapment....
-
Where Required: Multi-Story Buildings and Facilities [§206.2.3]
provisions in the Standards still apply to stories and mezzanines not served by an accessible route elevators provided anyway must fully comply (as standard or LULA elevators) vertical...
-
§ 38.23(b)(8) Platform entrance ramp
loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, measured on level ground, for a maximum rise of 3 inches, and the transition from roadway or sidewalk to ramp may be vertical...
-
Location: ADA Standard Section 206.3
Section 206.3 covers scoping requirements in the most current ADA Standards for the required locations of accessible routes.
-
Symmons® Canterbury Two Handle Widespread Lavatory Faucet SLW-4512-1.5
Feature Highlights: Two handle widespread lavatory faucet with quarter turn ceramic components. 8 - 16 inch centers for mounting Braided supply hoses Pop-up drain and lift rod...
-
Symmons® Degas Two Handle Widespread Lavatory Faucet SLW-5412-1.5
Pop-up drain and lift rod assembly 8 - 16 inch centers for mounting Aerator, 2.2 gpm flow rate (8.3 L/min) Polished chrome finish (standard) EPA WaterSenseR certified Tested and...
-
Symmons® Allura Two Handle Widespread Lavatory Faucet SLW-4712-1.5
Feature Highlights: Two handle widespread lavatory faucet with quarter turn ceramic components. 8 - 16 inch centers for mounting Braided supply hoses Pop-up drain and lift rod...
-
Husky 24" Line Generator Digital Laser Level
This level may use indoors or out for horizontal (level), vertical (plumb) and square alignment projects....
-
Clearances
The 80-inch minimum vertical clearance requirement remains for circulation areas and accessible routes in the queue line and load and unload areas....
-
§ 38.113(d)(1) Requirements
Vertical alignment may be accomplished by car air suspension, platform lifts or other devices, or any combination....
-
§ 38.83(b)(8) Platform entrance ramp
barrier used as a ramp, shall not exceed a slope of 1:8 measured on level ground, for a maximum rise of 3 inches, and the transition from the station platform or roadway to ramp may be vertical...
-
§ 38.95(b)(8) Platform entrance ramp
loading-edge barrier used as a ramp, shall not exceed a slope of 1:8, when measured on level ground, for a maximum rise of 3 inches, and the transition from station platform to ramp may be vertical...
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
Standing Supports (M304.3 and M305.3)
M305.3 also provides technical criteria for standing supports in horizontal and vertical positions....
