These surfaces may range between 4” to 5” in thickness - this will add to the vertical height of a stretcher when measuring from the floor to the top of the surface (uncompressed)....
Search Results "Vertical Rod"
Filters
Commonly Searched Documents
-
M301.2.1, M302.2.1 Transfer Height
-
206.2.3 Multi-Story Buildings and Facilities
Exceptions 1 – 7 are preempted by Florida vertical accessibility requirements of s. 553.509, F.S., as incorporated in section 201.1.1....
-
Symmons® Ballina Two Handle Widespread Lavatory Faucet SLW-5212-1.5
-1.5 Feature Highlights: Two handle widespread lavatory faucet with quarter turn ceramic components. 8 - 16 inch centers for mounting Braided hoses Pop-up drain and lift rod...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
M305.2 Transfer Supports
M305.2 Transfer Supports M305.2.2 Transfer Supports Structural Strength Proposed requirement: Transfer supports and their connections shall be capable of resisting vertical and...
-
404.2.10 Door and Gate Surfaces
Swinging door and gate surfaces within 10 inches (255 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
206.2.4 Spaces and Elements
Exceptions 1 – 3 are preempted by Florida vertical accessibility requirements of s.553.509, F.S., as incorporated in section 201.1.1....
-
Sight Lines
Sight Lines Both the horizontal and vertical viewing angles must be considered in the design of assembly areas....
-
Transfer Supports (M301.3.1, M302.3.1, and M305.2)
M305.2.2 would require the transfer supports and their connections to be capable of resisting vertical and horizontal forces of 250 pounds applied to all points of the transfer support....
-
R408.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
Running Slope
This may be expressed as the percentage of change in elevation (grade) or as a ratio of vertical distance to horizontal distance (running slope)....
-
1) Where the Standard specifically refers to 303
1) Where the Standard specifically refers to 303, such as 403.4 changes in level for walking surfaces: Here it is clear that changes in level that comply with either the ¼" maximum vertical...
-
Edge Protection [§405.9]
Edge protection is not required at: ramps no higher than 6” that have side flares ramp landings serving an adjoining run or stairway sides of ramp landings with vertical...
-
11B-704.5 TTY shelf
The shelf shall be capable of accommodating a TTY and shall have 6 inches (152 mm) minimum vertical clearance above the area where the TTY is to be placed....
-
§ 38.159(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
4.2 Stretchers
First, to serve these multiple purposes, the current configuration of stretchers must accommodate the vertical height needs of numerous components, including (Figure 3.1): the basic elements...
-
Surfaces (R302.7) (Section-by-Section Analysis)
Vertical alignment of surfaces within pedestrian access routes (including curb ramp runs, blended transitions, turning spaces, and gutter areas within pedestrian access routes) and within...
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
R405.1 General
Clearances are measured in relation to the usable clear space, not necessarily to the vertical support for an element....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
1008.3.2.3 Transfer Supports
Some examples of supports include a rope loop, a loop type handle, a slot in the edge of a flat horizontal or vertical member, poles or bars, or D rings on the corner posts....
-
7.4.5.1 Size
Vertical alignment at the intersection of the trails that form the T-shaped space shall be nominally level....
