(1) The position of any operable control shall be determined with respect to a vertical plane, which is 48 inches in length, centered on the operable control, and at the maximum protrusion...
Search Results "Counter Length"
-
§ 1194.25(j)(1)
-
Chapter 9: Built-In Elements
Chapter 9 covers built-in elements, including dining surfaces and work surfaces (902), benches (903), and sales and service counters (904)....
-
F. Check-In Areas
If a permanent reception counter is used for check in, make sure to provide a writing surface at an accessible height for people who use a wheelchair, scooter, or other mobility device....
-
Service
Keep lowered check-in counter clear. Where only high counters are available (older lodging facilities) train staff to come out from behind counter and provide a clipboard....
-
Guest Bathrooms
Portable shower benches must also meet the length, width, and depth requirements of a wall-hung bench. 610.2 Bathtub Seats....
-
4.34.6.4 WORK SURFACES
At least one 30 in (760 mm) section of counter shall provide a work surface that complies with the following requirements (see Fig. 50):...
-
Plan 3A: 12-Foot Wide Accessible Guest Room
The following accessible features are provided in the bathroom: • Comparable vanity counter top space (section 806); • Bathtub (section 607.2); • Removable bathtub seat (section...
-
Plan 1A: 13-Foot Wide Accessible Guest Room
The following accessible features are provided in the bathroom: • Comparable vanity counter top space (section 806); • Bathtub with a lavatory at the control end (section 607.2);...
-
Plan 1B: 13-Foot Wide Accessible Guest Room
The following accessible features are provided in the bathroom: • Comparable vanity counter top space (section 806); • Bathtub with a lavatory at the control end (section 607.2);...
-
Attachment I: Program Access in Existing Facilities
Attachment I: Program Access in Existing Facilities
-
11B-405.7.2.1
Where the ramp width is less than the top landing width additional landing length may be necessary to accommodate handrail extensions required to be in the direction of the ramp run without...
-
11B-505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
11B-403.7 Continuous gradient
All walks with continuous gradients shall have resting areas, 60 inches (1524 mm) in length, at intervals of 400 feet (121,920 mm) maximum....
-
11B-403.7 Continuous gradient
All walks with continuous gradients shall have resting areas, 60 inches (1524 mm) in length, at intervals of 400 feet (121,920 mm) maximum....
-
11B-505.3 Continuity
Handrails shall be continuous within the full length of each stair flight or ramp run....
-
§ 38.29(f)
(f) For vehicles in excess of 22 feet in length, the minimum interior height along the path from the lift to the securement location shall be 68 inches....
-
Example: Retail Facility
This example of a retail facility shows how scoping requirements for certain elements and spaces (sales counters and fitting rooms) apply and indicates employee work areas....
-
806 Transient Lodging Guest Rooms
Substantive changes made to this section revise requirements for: vanity counter spaces in accessible toilet or bathing rooms (806.2.4.1) wheelchair turning space (806.2.6...
-
11B-805.4.3 Turning space
Refer to the following examples: Exam room - Exam rooms are required to provide a turning space, accessible handwashing fixture, and 36-inch wide access along the full length...
-
Pass Through Kitchen
Clearances for pass through kitchens address counters, appliances, or cabinets on two opposing sides....
-
3) Restaurants
Contains requirements for counters and bars, access aisles, food service lines, tableware and condiment areas, raised speaker's platforms, and vending machine areas (but not controls)....
-
Vertical Alignment-Crest Vertical Curves
distance greater than length of vertical curve (S>L) Case 2-Sight distance less than lenght of vertical curve (S>L) For both equations, L = length of vertical curve...