(1) The sink and surrounding counter shall be mounted at a maximum height of 34 in (865 mm) above the floor, measured from the floor to the top of the counter surface, or shall be adjustable...
Search Results "Sink Faucet"
Filters
Commonly Searched Documents
-
4.34.6.5(1)
-
4.34.6.5(3)
(3) The depth of a sink bowl shall be no greater than 6-1/2 in (165 mm). Only one bowl of double- or triple-bowl sinks needs to meet this requirement....
-
606.5 Exposed Pipes and Surfaces
Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact....
-
Kohler Soho® Lavatory K-2053
This remarkably hard, glossy finish protects the surface for a clean, sanitary sink that maintains its polished shine through years of busy use....
-
608.5 Controls
Controls, faucets, and shower spray units shall comply with 309.4....
-
4.20.5 Controls
Faucets and other controls complying with 4.27.4 shall be located as shown in Fig. 34....
-
4.20.5 CONTROLS
Faucets and other controls complying with 4.27.4 shall be located as shown in Fig. 34....
-
11B-608.5.2 Standard roll-in type shower compartments
In standard roll-in type shower compartments, the controls, faucets, and the shower spray unit shall be located on the back wall of the compartment adjacent to the seat 16 inches (406 mm...
-
11B-606.5 Exposed pipes and surfaces
Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact....
-
606.5 Exposed Pipes and Surfaces
Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact....
-
ADAPTABLE
As part of the initial design and construction, for example, structural backing would be provided for the later installation of grab bars, base cabinets under kitchen sinks would be removable...
-
4.34.5.4(4) Controls
Faucets and other controls shall be located as shown in Fig. 34 and shall comply with 4.27.4....
-
4.34.6.5(4)
(4) Faucets shall comply with 4.27.4. Lever-operated or push-type mechanisms are two acceptable designs....
-
11B-606.6 Adjacent side wall or partition
ETA Editor's Note The positioning requirement prescribed by CBC 11B-606.6 applies to lavatories, not to sinks....
-
Attachment H: Modifications to Altered Facilities
Attachment H: Modifications to Altered Facilities
-
11B-608.8 Shower enclosures
Enclosures for shower compartments shall not obstruct controls, faucets, and shower spray units or obstruct transfer from wheelchairs onto shower seats....
-
608.8 Shower Enclosures
Enclosures for shower compartments shall not obstruct controls, faucets, and shower spray units or obstruct transfer from wheelchairs onto shower seats....
-
11B-608.8 Shower enclosures
Enclosures for shower compartments shall not obstruct controls, faucets, and shower spray units or obstruct transfer from wheelchairs onto shower seats....
-
608.5.2 Standard Roll-In Type Shower Compartments
In standard roll-in type shower compartments, the controls, faucets, and shower spray unit shall be located above the grab bar, but no higher than 48 inches (1220 mm) above the shower floor...
-
4.34.6.5(7)
(7) A clear floor space 30 in by 48 in (760 mm by 1220 mm) shall allow forward approach to the sink....
-
Sec.36.403(f)(2)(ii)
(ii) Costs associated with making restrooms accessible, such as installing grab bars, enlarging toilet stalls, insulating pipes, or installing accessible faucet controls;...
-
§ 35.151(b)(4)(iii)(B)(2)
(2) Costs associated with making restrooms accessible, such as installing grab bars, enlarging toilet stalls, insulating pipes, or installing accessible faucet controls;...
-
§ 36.403(f)(2)(ii)
(ii) Costs associated with making restrooms accessible, such as installing grab bars, enlarging toilet stalls, insulating pipes, or installing accessible faucet controls;...
-
§ 35.151(b)(4)(iii)(B)(2)
(2) Costs associated with making restrooms accessible, such as installing grab bars, enlarging toilet stalls, insulating pipes, or installing accessible faucet controls;...
