Reach ranges for persons seated in wheelchairs may be further clarified by Fig. A3(a). These drawings approximate in the plan view the information shown in Fig. 4, 5, and...
Search Results "Pull Side"
Filters
Commonly Searched Documents
-
A4.2.5 & A4.2.6 Reach
-
A4.2.5 & A4.2.6 REACH
Reach ranges for persons seated in wheelchairs may be further clarified by Fig. A3(a). These drawings approximate in the plan view information shown in Fig. 4, 5, and 6 in other...
-
Midmark 647 Barrier-Free® Power Podiatry Procedures Chair
plush design for highend appearance and unparalleled comfort Programmability: Three positions that you customize to your needs Electrical Outlets: Duplex, hospital grade (on each side...
-
2. c. REACH RANGES
Figure 18 (high forward reach range), and Figure 19 (side reach range) illustrate reach ranges accessible to wheelchair users or people with limited mobility....
-
M301.2.3 Size (Section-by-Section Analysis)
The MDE NPRM proposed a transfer surface size for diagnostic equipment used in the supine, prone, or side-lying position of 30 inches wide and 15 inches deep minimum....
-
Doors
DOORS 32” clear width 11B-404.2.3 Maneuvering clearances 11B-404.2.4.1 Level landings each side...
-
Doors
DOORS 32” clear width 11B-404.2.3 Maneuvering clearances 11B-404.2.4.1 Level landings each side...
-
A4.17.3 Size and Arrangement
A standard stall provides a clear space on one side of the water closet to enable persons who use wheelchairs to perform a side or diagonal transfer from the wheelchair to the water closet...
-
M301.1 General
Where diagnostic equipment is used by patients in a supine, prone, or side-lying position, it shall comply with M301....
-
Just Manufacturing 42" Stainless Steel Grab Bar
Type-304, 18 Gauge Stainless Steel 42" Length x 1-1/2" Diameter with concealed screws Brushed stainless finish Grab bar to wall distance...
-
Bobrick 42" Straight Grab Bar Peened B-6806.99 x 42
42" (1065mm) long, 1-1/2" (38mm) dia. tubing, peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
Bobrick 42" Straight Grab Bar Peened B-5806.99 x 42
42" (1065mm) long, 1-1/4" (32mm) dia. tubing, peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
Bobrick 42" Straight Grab Bar B-6806 x 42
42" (1065mm) long, 1-1/2" (38mm) dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick 42" Straight Grab Bar B-5806 x 42
42" (1065mm) long, 1-1/4" (32mm) dia. tubing. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Moen Home Care Peened 42" Grab Bar
Safety, comfort and peace of mind. It's engineered into every Moen Home Care® product we make. the securemount design allows for secure installation into any stud at any...
-
M301.2.3 Size
The size of transfer surfaces shall be measured from center points of their opposing sides....
-
A4.27.3 Height
Fig. A8 further illustrates mandatory and advisory control mounting height provisions for typical equipment. Electrical receptacles installed to serve individual...
-
3.5.3 Signs in General
If materials need to be obtained from or manipulated on a sign or kiosk, the sign or kiosk shall be designed to meet the reach ranges in section 308 of the ABAAS.
-
5.2.1.1 Transfer Surface Width
The transfer surface should be 28 inches wide minimum for equipment used by patients in a supine, side-lying, or prone position....
-
Honeywell Fire-Lite Alarm BG-12 Series
PUSH IN/PULL DOWN handle latches in the down position to clearly indicate the station has been operated. Multiple hex- and key-lock models available....
-
Brewer Access™ High-Low Exam Table
supports the patient's back Chair-to-Table design takes patient from consulation to examination Standard patient transfer grab bars provides extra security Patented pass-through side...
-
5.2.1.2 Transfer Surface Depth
The transfer surface should be 17 inches deep minimum for all equipment used by patients in a supine, side-lying, or prone position with the exception of imaging equipment....
-
M301.1 General
Diagnostic equipment that supports patients in a supine, prone, or side-lying position shall comply with M301. ...
