Required guards shall not be less than 42 inches (1067 mm) high, measured vertically as follows: From the adjacent walking surfaces....
Search Results "Assurances from Contractors"
-
1015.3 Height
-
1015.3 Height
Required guards shall not be less than 42 inches (1067 mm) high, measured vertically as follows: From the adjacent walking surfaces....
-
EXHIBIT H POLICY OF NONDISCRIMINATION ON THE BASIS OF DISABILITY IN EFFECTIVE WEBSITE COMMUNICATIONS
QuikTrip will ensure that persons with disabilities have an equal opportunity to benefit from the goods, services, privileges, advantages, and accommodations offered by QuikTrip through...
-
11B-104.1.1 Construction and manufacturing tolerances
Information on specific tolerances may be available from industry or trade organizations, code groups and building officials, and published references....
-
11B-104.1.1 Construction and manufacturing tolerances
Information on specific tolerances may be available from industry or trade organizations, code groups and building officials, and published references. ...
-
II. COMPLIANCE WITH TITLE III OF THE ADA
provide a copy of the policy to each new Web Content Personnel, contractor responsible for web content, and CSO Personnel for www.hrblock.com; c. ...
-
Spout Location: ADA Standard Section 602.5
Section 602.5 covers the current ADA Standards for the spout location of drinking fountains.
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers....
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers....
-
Figure 404.2.4.1(k) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Push Side with Closer – Drawing from the U.S. Access Board
-
Figure 404.2.4.1(i) Maneuvering Clearances at Manual Swinging Doors and Gates: Latch Approach, Pull Side with Closer – Drawing from the U.S. Access Board
-
Door Closers and Gate Closers: ADA Standard Section 404.2.8.1
Section 404.2.8.1 covers the current ADA Standards for the closing speed of door closers and gate closers.
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
D. Technical standards for construct validity studies
Users choosing to justify use of a selection procedure by this strategy should therefore take particular care to assure that the validity study meets the standards set forth below....
-
Rebuilding Together East Bay-North - Berkeley, CA
We can only do this with the support of roughly 1,000 volunteers and donations from individuals, corporations, private foundations, and small business owners....
-
Size: ADA Standard Section 604.3.1
Section 604.3.1 covers the current ADA Standards for the size of the water closet clearance.
-
B.2.ii. - How should an agency proceed in identifying "applicable" technical provisions in Subparts B, C, and D of the Access Board’s standards to ensure acquired products provide comparable access?
For example, if an agency were to enter into a seat management contract for desktop computing resources, the hardware and software to be provided by the contractor would be required to meet...
-
Conventions Used In This Guide
Font Convention Meaning Black Text Used for text taken from CBC Black Text, Italicized...
-
Conventions Used In This Guide
Font Convention Meaning Black Text Used for text taken from CBC Black Text, Italicized...
-
Introduction
impairments, but also members of the park’s exhibit planning, cultural resources compliance staff, interpretive staff and Diversity Committee staff, representatives of the wayside design contractor...
-
Maintenance
The playground crews ranged in number from 1‒3 staff, usually with one full-time employee and 2‒3 seasonal staff during the summer months. At least 30 minutes was spent on site. ...
-
Accessibility - Flatness and Lippage
For any application, a tiled floor should comply with the flatness requirements in ANSI A108.02: "no variations exceeding 1/4" in 10 feet from the required plane."...
-
Doors: ADA Standard Section 604.8.1.2
Section 604.8.1.2 covers the current ADA Standards for wheelchair accessible compartment doors.
