Ramps shall comply with R407....
Search Results "Ramp Handrail"
Filters
Commonly Searched Documents
-
R407.1 General
-
11B-1007.2 Accessible routes
Ramp landing slopes specified by Section 11B-405.7.1 shall be permitted to be 1:20 maximum. 5. ...
-
11B-1007.2 Accessible routes
Ramp landing slopes specified by Section 11B-405.7.1 shall be permitted to be 1:20 maximum. 5....
-
§ 38.23(c) Vehicle ramp
(c) Vehicle ramp—...
-
Curb Ramps and Blended Transitions (R309.4) (Section-by-Section Analysis)
Curb Ramps and Blended Transitions (R309.4) (Section-by-Section Analysis) Curb ramps or blended transitions must connect the access aisle serving each accessible on-street parking space...
-
4.8.7 Edge Protection
Ramps and landings with drop-offs shall have curbs, walls, railings, or projecting surfaces that prevent people from slipping off the ramp....
-
4.8.7 EDGE PROTECTION
Ramps and landings with drop-offs shall have curbs, walls, railings, or projecting surfaces that prevent people from slipping off the ramp....
-
11B-705.1.2.2.2.2 Two entrance/exit points
Where the turning space has two entrance/exit points other than the sloped ramp segments, detectable warnings shall be 36 inches (914 mm) deep at both entrance/ exit points, as measured...
-
Boarding Piers at Boat Launch Ramps
ADAAG ramp requirements do not apply to the portion of the accessible route serving a floating boarding pier or skid pier if it is located within a boat launch ramp....
-
T303.2 Edges
Edges shall be rounded or eased.
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
11B-1008.2.5.3.1 Handrail gripping surfaces
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 0.95 inch (24 mm) minimum and 1.55 inches (39 mm) maximum....
-
DSA Drawing 11B-406-8 Parallel Curb Ramp with No Gutter (2016 CBC)
Requires the Premium User plan or above. (Login or upgrade your account!) -
Diagonal Curb Ramps
Section 406.6 provides specifications for diagonal (or corner type) curb ramps. These curb ramps must have a 48 inch minimum clear space at the bottom....
-
B7. Curb Ramp Width
Is the width of the curb ramp surface at least 36 inches? [ADA Stds 4.7.3] Yes _____ No _____...
-
11B-406.5.5 Wet conditions
Curb ramps and blended transitions shall comply with Section 11B-405.10....
-
Launch Ramps Without Boarding Piers
Launch Ramps Without Boarding Piers There are no specific provisions that address access to launch ramps without boarding piers....
-
Stair widths
Section 1009.3 states that in order to be a part of the accessible means of egress between stories, stairs shall have a clear width of 48" BETWEEN the handrails....
-
Circular Cross Section and Clearance (§505.5, §505.7)
Circular Cross Section and Clearance
-
Section 35.151(i) Curb Ramps (Section-by-Section Analysis)
The current § 35.151(e) on curb ramps has been redesignated as § 35.151(i). ...
-
Section 35.151(i) Curb ramps (Section-by-Section Analysis)
Section 35.151(i) Curb ramps (Section-by-Section Analysis) Section 35.151(e) on curb ramps in the 1991 rule has been redesignated as § 35.151(i)....
-
1.2.5 Ramps
1.2.5 Ramps. When overall running slope and cross slope for accessible ramps are measured according to Sections 1.1.11 a recommended tolerance for these slopes is +0.5%....
-
R304 Curb Ramps and Blended Transitions (Section-by-Section Analysis)
R304 Curb Ramps and Blended Transitions (Section-by-Section Analysis)...
