Seats shall not be sprung to return to a lifted position....
Search Results "Handrail Return"
-
11B-604.9.3 Height
-
AquaTrek2 ADA Step System
MEETS OR EXCEEDS ADA REQUIREMENTS: No Open Risers 7” Maximum Riser Height 12” Minimum Tread Depth 24” Maximum Width Between Handrails Top Landing...
-
405.5 Clear Width
The clear width of a ramp run and, where handrails are provided, the clear width between handrails shall be 36 inches (915 mm) minimum....
-
§8.56(h)(2)
(2) The reviewing civil rights official shall send by certified mail, return receipt requested, a copy of the request for review to the other party, if any....
-
§ 37.153(a)
If necessary, the Administrator will return the application with a request for additional information....
-
AquaTrek2 ADA Ladder System
With a full 12 inch tread depth along with inside stepped handrails that provide a horizontal hand grab with a horizontal foot step....
-
§382.125(c)
(c) You must provide for the checking and timely return of passengers' wheelchairs, other mobility aids, and other assistive devices as close as possible to the door of the aircraft, so...
-
§382.7(d)
(d) As a foreign carrier, if you operate a charter flight from a foreign airport to a U.S. airport, and return to a foreign airport, and you do not pick up any passengers in the U.S., the...
-
Stability or Stable Surface
A stable surface is one that remains unchanged by contaminants or applied force, so that when the contaminant or force is removed, the surface returns to its original condition (2010 ADA...
-
1132A.8.1 Lever-type hardware
The lever or lever of actuated latches or locks shall be curved with a return to within ½ inch (12.7 mm) of the door to prevent catching on the clothing of persons during egress in Group...
-
§ 37.203(c)
is discovered to be inoperative, the entity shall take the vehicle out of service before the beginning of the vehicle's next trip and ensure that the lift is repaired before the vehicle returns...
-
1132A.8.1 Lever-type hardware
The lever or lever of actuated latches or locks shall be curved with a return to within ½ inch (12.7 mm) of the door to prevent catching on the clothing of persons during egress in Group...
-
1.1.14 Flatness of ramp cross slope
For ramps up to and including 5 ft (1525 mm) wide between the handrails, measure cross slope in the center of the ramp. See Fig. 6(a)....
-
A Word about Benefit Programs
A Word about Benefit Programs You have probably already received information from your service branch or the Department of Veterans Affairs about programs designed to assist returning...
-
§ 37.163(d)
discovered to be inoperative, the entity shall take the vehicle out of service before the beginning of the vehicle's next service day and ensure that the lift is repaired before the vehicle returns...
-
1.1.13 Flatness of ramp running slope
Each line should be approximately 6 in. (150 mm) from the inside (ramp side) edge of the handrail....
-
11B-303.5 Warning curbs
A warning curb is not required when a guard or handrail is provided with a guide rail centered 2 inches (51 mm) minimum and 4 inches (102 mm) maximum above the surface of the walk or sidewalk...
-
11B-303.5 Warning curbs
A warning curb is not required when a guard or handrail is provided with a guide rail centered 2 inches (51 mm) minimum and 4 inches (102 mm) maximum above the surface of the walk or sidewalk...
-
11B-407.4.10 Support rail
Support rails in elevator cabs are used in a different way than handrails along a walking surface such as a ramp or stairway....
-
210 and 504 Stairways
require all newly constructed stairs that are part of a means of egress to comply with the requirements for accessible stairs, which include requirements for accessible treads, risers, and handrails...
-
f-iv
At least 36 inches between handrails 2. Top landing part of walk 3. Bottom landing part of walk 4. Handrail height 34 to 38 inches 5. Edge protection....
-
T303.1 General
Handrails, stanchions, and handholds in non-rail vehicles shall comply with T303....
-
1132A.8.1 Lever-type hardware
The lever or lever of actuated latches or locks shall be curved with a return to within ½ inch (12.7 mm) of the door to prevent catching on the clothing of persons during egress in Group...
-
Edge Protection: ADA Standard Section 405.9
Section 405.9 covers the current ADA Standards for edge protection at ramps.
