ETA Editor’s Note: The 1991 ADA Standards allowed construction tolerances from an 18” absolute dimension. ...
Search Results "ASCII: American Standard Code for Information Interexchange"
-
604.2 Location
-
3. EXCLUSIONS
The following facilities need not comply with these DoD Standards: Facilities, or portions of facilities, on a military installation 4 that are designed and constructed for use...
-
Equipment and furniture. (Section-by-Section Analysis)
establish specific equipment requirements at that time because the requirements could be addressed under other sections of the regulation and because there were no appropriate accessibility standards...
-
413.1 General (Section-by-Section Analysis)
The requirements in proposed 413.1 would be new to the 508 Standards and the 255 Guidelines....
-
General: ADA Standard Section 702.1
Fire alarm systems shall have permanently installed audible and visible alarms complying with NFPA 72 (1999 or 2002 edition) (incorporated by reference, see “Referenced Standards” in Chapter...
-
Dimensions: ADA Standard Section 810.2.2
Access Board’s Note to Reader: The Department of Transportation’s ADA standards indicate that compliance is required to the extent construction specifications are within a public entity's...
-
Rath Microtech Line Powered Elevator Emergency Phone 2400-808DO
Dimensions: 10-5/8”W x 12-1/2”H x 2”D Brushed Stainless Steel Face Plate Mounts via 4 screw holes in corners ADA & B44 Code Compliant Dials up to 2 emergency numbers Program...
-
Guest Rooms with Communication Features: ADA Standard Section 806.3
For headset or external amplification system compatibility, a standard subminiature jack installed in the telephone will provide the most flexibility....
-
Section 1193.2 Scoping (Section-by-Section Analysis)
Several manufacturers drew analogies to portions of facilities covered by the Americans with Disabilities Act (ADA), such as stadium seats, hotel rooms, and telephones in a bank as giving...
-
Edge Protection [4.8.7]
Vertical balusters can be used; intermediate spacing is not specified by ADAAG but is commonly covered by local codes....
-
230 and 708 Two-Way Communication Systems
230 and 708 Two-Way Communication Systems New provisions of the 2010 Standards at sections 230.1 and 708 require two-way communications systems to be equipped with visible as well as...
-
§382.13(a)
As a carrier, you must modify your policies, practices, and facilities when needed to provide nondiscriminatory service to a particular individual with a disability, consistent with the standards...
-
§ 36.406(a)(2)
(2) New construction and alterations subject to this part shall comply with the proposed standards if physical construction of the property commences on or after [date six months after the...
-
§ 36.406(a)(1)
(1) New construction and alterations subject to this part shall comply with the 1991 Standards if physical construction of the property commences before [date six months after the effective...
-
408.3.2.1 Power Operation
Swinging doors shall be power-operated and shall comply with ANSI/BHMA A156.19 (1997 or 2002 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
f-v
[ADA Standards §§ 4.11.2, 4.27.3] Yes No...
-
I3
[ADA Standards § 4.31.9 (2)] Yes No...
-
M21
[ADA Standards § 4.25.3] Yes No...
-
K5
[ADA Standards § 5.5] Yes No...
-
B2
[ADA Standards § 4.6.3] Yes No...
-
Sec.36.308(b) New construction and alterations
The provision and location of wheelchair seating spaces in newly constructed or altered assembly areas shall be governed by the standards for new construction and alterations in subpart...
-
4.1.6(1)(e)
alteration work is limited solely to the electrical, mechanical, or plumbing system and does not involve the alteration of any elements and spaces required to be accessible under these standards...
-
A4.8.5 HANDRAILS
The requirements for stair and ramp handrails in this standard are for adults....
-
§1193.51(e) TTY signal compatibility
Products, including those providing voice communication functionality, shall support use of all cross-manufacturer non-proprietary standard signals used by TTYs....
