NFPA 72®, National Fire Alarm Code, defines a notification appliance as "a fire alarm system component such as a bell, horn, speaker, light, or text display that provides audible, tactile...
Search Results "Fire-Building Surface"
Filters
Commonly Searched Documents
-
Occupant Notification System
-
Visual Alarms
Activation of visual appliances in work areas on an as-needed basis does not provide a practicable solution as most codes, standards, and local laws prohibit deactivation of fire alarm appliances...
-
Stable
A surface is not permanently affected by expected weather conditions and can sustain normal wear and tear from the expected use(s) of the area, between planned maintenance....
-
11B-233.3.1.2.2 Non-elevator buildings
ETA Editor's Note This section of the 2019 California Building Code was amended by the Division of the State Architect....
-
206.4 Entrances
Where an alteration includes alterations to an entrance, and the building or facility has another entrance complying with 404 that is on an accessible route, the altered entrance shall not...
-
F206.4 Entrances
Where an alteration includes alterations to an entrance, and the building or facility has another entrance complying with 404 that is on an accessible route, the altered entrance shall not...
-
206.4 Entrances
Where an alteration includes alterations to an entrance, and the building or facility has another entrance complying with 404 that is on an accessible route, the altered entrance shall not...
-
M304.2 Standing Surface
The surface on which the patient stands shall be slip resistant....
-
11B-609.5 Surface hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
11B-609.5 Surface hazards
Grab bars and any wall or other surfaces adjacent to grab bars shall be free of sharp or abrasive elements and shall have rounded edges....
-
M304.2 Standing Surface
Equipment surfaces on which patients stand must comply with M304.2...
-
TechniSoil G3® Pathway Liquid Polymer Stabilizer
This eco-friendly liquid polymer stabilizer for decomposed granite (DG) and crushed stone materials yields a durable, dust-free surface in only a few basic steps....
-
1009.12 Alarms/emergency warning systems/accessibility
Emergency warning systems as part of the fire alarm system shall be designed and installed in accordance with NFPA 72 as amended in Chapter 35....
-
1009.12 Alarms/emergency warning systems/accessibility
Emergency warning systems as part of the fire-alarm system shall be designed and installed in accordance with NFPA 72 as amended in Chapter 35....
-
907.2.1.2 Emergency power
Emergency voice/alarm communications systems shall be provided with an approved emergency power source.
-
4.28.3(7)
(7) In general, no place in any room or space required to have a visual signal appliance shall be more than 50 ft (15 m) from the signal (in the horizontal plane). In large rooms and...
-
4.28.3(8)
(8) No place in common corridors or hallways in which visual alarm signalling appliances are required shall be more than 50 ft (15 m) from the signal.
-
A4.28.3 Visual Alarms
The specifications in this section do not preclude the use of zoned or coded alarm systems.
-
4.28.3(6)
(6) The appliance shall be placed 80 in (2030 mm) above the highest floor level within the space or 6 in (152 mm) below the ceiling, whichever is lower.
-
4.28.1 GENERAL
Alarm systems required to be accessible by 4.1 shall comply with 4.28.
-
A4.28.3 VISUAL ALARMS
The specifications in this section do not preclude the use of zoned or coded alarm systems. In zoned systems, the emergency exit lights in an area will flash whenever an audible...
-
409.4.2 Floor Surfaces
409.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303....
-
1.1.3 Scope
this code shall apply to the construction, alteration, movement, enlargement, replacement, repair, equipment, use and occupancy, location, maintenance, removal and demolition of every building...
-
Aluminum Heavy Duty Wheels n' Heels® InVent Grating
The major difference with the InVent style is that the main support bearing bars are hidden under the top surface bars and run in the direction perpendicular to the top surface bars....
