Two were renovated using the ADA Standards for Accessible Design and are accessible to children and adults with disabilities, two are not accessible....
Search Results "Adult Dimension"
Filters
Commonly Searched Documents
-
More on Notice
-
AssistiveWare Proloquo2Go
effort Share vocabularies and folders between users and devices Let your voice be heard Download over 60 English, French and Spanish natural-sounding Text to Speech adult...
-
Selection of Variables
] E Measurements of chair and user (floor to top of head, side to side, back to front, height to armrest, height to seat) [accessibility] The two most basic dimensions...
-
8.1 Excluded Populations Needing Future Attention
8.1 Excluded Populations Needing Future Attention The statutory authority of the MDE Advisory Committee applied only to adults with disabilities not to pediatric populations....
-
Ambulatory Accessible Compartment
Throughout the new guidelines, the Board has sought to specify dimensions as a range instead of in absolute terms where practicable to facilitate compliance without compromising accessibility...
-
5.3.2.1 Transfer Sides Recommendation for Stretchers
5.3.2.1 Transfer Sides Recommendation for Stretchers On stretchers, the transfer surface is oriented along the long dimension of the surface on which patients are in the supine, prone...
-
604.2 Location
ETA Editor’s Note: The prior standards allowed construction tolerances to occur on either side of an 18” absolute dimension....
-
9. Exterior Ramps
[ADA Stds. 4.8.3] Yes __ No __ N/A __ Comments: _______________________________ d. do the exterior ramps have running slopes that are 1:12 or less (critical dimension of 2" or less...
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADAS] 405.7.5 Doorways. ...
-
Platform Edges
This depth is an absolute dimension, not a minimum. Some platforms are edged with a buffer material that is designed to break away if hit by cargo trains....
-
505.6 Gripping Surface
distance between horizontal projections and the bottom of the gripping surface shall be permitted to be reduced by 1/8 inch (3.2 mm) for each 1/2 inch (13 mm) of additional handrail perimeter dimension...
-
4.4.4 Clear Floor or Ground Space
The long dimension of the clear space shall be roughly perpendicular to the length of the bench....
-
Department of Justice method
Use the tape measure and measure the open gap at the downhill end of the level to establish the critical dimension....
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADAS] 405.7.5 Doorways....
-
11B-703.7.2.1 International Symbol of Accessibility
A border may be provided inside or outside of the minimum required International Symbol of Accessibility dimension....
-
Direct Threat
Examples A state agency organizes a job placement event for young adults ages 18-21. I.R. is 25 and is hard of hearing....
-
232.2 General Holding Cells and General Housing Cells
., male/female and adult/juvenile) to facilitate access....
-
U.N. Convention on the Rights of Persons with Disabilities (CRPD)
The Convention is intended as a human rights instrument with an explicit, social development dimension....
-
4.3.4 Knee and Toe Clearances
The following dimensions on knee and toe clearances should be used to accommodate 95% of our study sample on all four dimensions: • Toe clearance depth: 127 mm (5 in.) maximum, measured...
-
4.3.1 Reference WhMD Users
The Reference Users should include plan and elevation drawings and have key dimensions coded with a corresponding table of values for each code showing the 5th, 25th, 50th, 75th and 95th...
-
Combination Wheelchair/Horse Accessible Gates
The gate dimensions work well together because the required turning diameter for a wheelchair is 60 inches....
-
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment On imaging equipment, the transfer surface is oriented along the long dimension of the surface where...
-
Clear Floor Space [4.35.2]
Recommendations: Consider additional space on the narrow dimension to allow alternative transfers. Some people may need to fully recline to dress or change clothes....
-
4.21.2 Size and Clearances
Institutional showers exceeded the minimum stall dimensions....
