Latch bolt height to finished floor 40 3/32" (1018mm) at center Crossbar projection — neutral 3 3/4" (95mm), depressed 2 3/8" (60mm) Crossbar length 42" (1067mm) Lock stile case 7 1/...
Search Results "9-1-1 Service"
Filters
Commonly Searched Documents
-
Allegion Von Duprin 55 Series Cross Bar Exit Devices
-
2. Follow the Accessibility Standards for Play Areas
Two exceptions may be applied: 1) In play areas less than 1000 square feet, the clear width of accessible routes shall be permitted to be 44 inches minimum, if at least one turning space...
-
11B-213.3.1 Toilet compartments
When the July 1, 2015 Supplement to the 2013 CBC was issued, this scoping was increased, thereby exceeding the 2010 ADAS scoping at large multi-user toilet rooms....
-
Smooth Surface
This provision requires that parts creating joints in the smooth surface are to be within 1/16 inch of the same plane as the other....
-
§ 382.5 Individual with a disability
As used in this definition, the phrase: (a) Physical or mental impairment means: (1) any physiological disorder or condition, cosmetic disfigurement, or anatomical loss affecting one...
-
§382.3 Individual with a disability
As used in this definition, the phrase: (a) Physical or mental impairment means: (1) Any physiological disorder or condition, cosmetic disfigurement, or anatomical loss affecting one...
-
F104.1.1 Construction and Manufacturing Tolerances
For example, if this document requires "1½ inches," avoid specifying "1½ inches plus or minus X inches."...
-
Passing Spaces [1016.4]
When passing spaces and resting intervals overlap, the technical requirements for resting intervals apply and the slope of the surface must be no steeper than 1:48 (2 percent) in any direction...
-
M301.2.3 Transfer Sides
Obstructions shall not be vertically less than 1" (25 mm) nor be horizontally more than 3" (75 mm) from the edge of the patient support surface provide unobstructed access to the transfer...
-
NAADAC Webinar Series: "ADA: The Next Generation" - Virtual and At-Home Training
ADA: The Next Generation: Seven Part Webinar Series (total 12 hours): Overview of Title II and III Regulations, Part 1 (10/6/10), Run time: 1.5 hrs Overview of Title II...
-
1013.3 Height
Required guards shall not be less than 42 inches (1067 mm) high, measured vertically as follows: 1. From the adjacent walking surfaces; 2. ...
-
1017.4 Passing Spaces
Where passing spaces and resting intervals overlap, the technical requirements for resting intervals in 1017.8.3 require the slope of the surface to not be steeper than 1:48 in any direction...
-
Paragraph (b) (Advisory Guidance)
Paragraph (b) Operable with Low Vision and Limited or no Hearing 1. Individuals with low vision often also have hearing disabilities, especially older individuals....
-
Section 1194.26 Desktop and Portable Computers (Preamble, Section-by-Section Analysis)
These provisions are addressed further in sections 1194.23 (k) (1) through (4) above. (See §1194.23(a) in the NPRM.)...
-
Accessible Routes - Interior and Exterior
ADA Standards 4.1.2 (1); 4.1.3(1); 4.3. At least one route that is a minimum of 36 inches wide without steps, stairs, or other abrupt level changes must be provided...
-
TownSteel "V" Rose Tubular Lockset
Specifications: Door Thickness 1-3/4" standard, other upon request Backset 2-3/4" standard, 2-3/8" available Rose Wrought brass or zinc alloy, 2-39/64" x 43/64" Lever Brass or zinc...
-
TownSteel "L" Rose Tubular Lockset
Specifications: Door Thickness 1-3/4" standard, other upon request Backset 2-3/4" standard, 2-3/8" available Rose Wrought steel, brass or stainless steel, 2-17/32" x 13/32" Lever...
-
TownSteel "S" Rose Tubular Lockset
Specifications: Door Thickness 1-3/4" standard, other upon request Backset 2-3/4" standard, 2-3/8" available Rose Wrought brass or stainless steel, 2-33/64" x 2-33/64 x 5/32" Lever...
-
TownSteel "B" Rose Tubular Lockset
Specifications: Door Thickness 1-3/4" standard, other upon request Backset 2-3/4" standard, 2-3/8" available Rose Wrought brass, 2-17/32" x 7/16" Lever Brass or Zinc Alloy, refer...
-
TownSteel "H" Rose Tubular Lockset
Specifications: Door Thickness 1-3/4" standard, other upon request Backset 2-3/4" standard, 2-3/8" available Rose Wrought brass, 2-13/16" x 2-13/16" x 13/32" Lever Brass or Zinc...
-
TownSteel "F" Rose Tubular Lockset
Specifications: Door Thickness 1-3/4" standard, other upon request Backset 2-3/4" standard, 2-3/8" available Rose Wrought brass or stainless steel, 2-17/32" x 5/32" Lever Brass,...
-
AJW Architectural Products U719 96"W x 48"H J-Mold Mirror - Four Sided Frame - Plate Glass
finish Mirror features a "J" type channel frame Multiple reflective surfaces available Mirror comes with a 15 year warranty against silver spoilage Product Specs Mirror: 1/...
-
3.2 Non-discrimination Legislation.
The following websites contain relevant information concerning disability legislation and how it applies to an airport setting. 1....
-
1.4 Related Reading Material.
1. DOJ ADA, Title II, Technical Assistance Manual, and Supplements, http://www.ada.gov/taman2.html. 2....
