When amusement rides are in the load and unload position, wheelchair spaces complying with Section 11B-1002.4, amusement ride seats designed for transfer complying with Section 11B-1002.5...
Search Results "Seat Location"
-
11B-206.2.9.2 Wheelchair spaces, ride seats designed for transfer, and transfer devices
-
Alternate Roll-In Type Shower Compartments: ADA Standard Section 608.5.3
Section 608.5.3 covers the current ADA Standards for controls in alternate roll-in type shower compartments.
-
11B-604.9 Water closets and toilet compartments for children's use
Water Closet Centerline 12 inches (305 mm) 12 to 15 inches (305 to 381 mm) 15 to 18 inches (381 to 457 mm) Toilet Seat...
-
11B-604.9 Water closets and toilet compartments for children's use
Water Closet Centerline 12 inches (305 mm) 12 to 15 inches (305 to 381 mm) 15 to 18 inches (381 to 457 mm) Toilet Seat...
-
11B-608.5.3 Alternate roll-in type shower compartments
and 27 inches (686 mm) maximum from the seat wall or shall be located on the back wall opposite the seat 15 inches (381 mm) maximum, left or right of the centerline of the seat....
-
11B-608.5.3 Alternate roll-in type shower compartments
and 27 inches (686 mm) maximum from the seat wall or shall be located on the back wall opposite the seat 15 inches (381 mm) maximum, left or right of the centerline of the seat....
-
802.2.1 Lines of Sight Over Seated Spectators
Where spectators are expected to remain seated during events, spectators in wheelchair spaces shall be afforded lines of sight complying with 802.2.1....
-
Sec.36.304(b)(15)
(15) Installing a raised toilet seat;...
-
§ 36.304(b)(15)
(15) Installing a raised toilet seat;...
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Where an amusement ride provides shoulder-to-shoulder seating, companion seats shall be shoulder-to-shoulder with the adjacent wheelchair space....
-
4.30.6 Mounting Location and Height
4.30.6 Mounting Location and Height. Where permanent identification is provided for rooms and spaces, signs shall be installed on the wall adjacent to the latch side of the door....
-
A4.1.3(19)(a)
Folding seating units are usually two fixed seats that can be easily folded into a fixed center bar to allow for one or two open spaces for wheelchair users when necessary....
-
802.2.1 Lines of Sight over Seated Spectators
Where spectators are expected to remain seated during events, spectators in wheelchair spaces shall be afforded lines of sight complying with 802.2.1. [ECTCR UFAS 4.33.3]...
-
Seat Height
Seat Height The lift must be designed so that the seat will make a stop between a minimum of 16 inches and maximum of 19 inches (measured from the deck to the top of the seat surface,...
-
4.32.1 Minimum Number
Fixed or built-in seating or tables required to be accessible by 4.1 shall comply with 4.32....
-
M303 Diagnostic Equipment Used by Patients Seated in Wheelchair
M303 provides technical criteria for diagnostic equipment used by patients seated in a wheelchair....
-
Fraudulent purchase of designated accessible seating. (Section-by-Section Analysis)
Moreover, the Department recognizes that the implementation of some of its proposals, such as those relating to the public identification of accessible seating, increase the potential for...
-
206.4.4.1 Location
206.4.4.1 Location....
-
4.30.6 MOUNTING LOCATION AND HEIGHT
Interior signage shall be located alongside the door on the latch side and shall be mounted at a height of between 54 in and 66 in (1370 mm and 1675 mm) above the finished floor....
-
4.32.1 MINIMUM NUMBER
Fixed or built-in seating, tables, or work surfaces required to be accessible by 4.1 shall comply with 4.32....
-
Height Above Finish Floor or Ground: ADA Standard Section 703.4.1
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches...
-
6.9
plan design uses the same ratio of (i) the total number of seats in the same row as the wheelchair location plus all the seats in the rows between the wheelchair location and the screen...
-
Transfer Surface Size – M302.2.2 Seated Position
Transfer Surface Size – M302.2.2 Seated Position The issue of seat depth was discussed and decided during the full committee meetings as follows: depth of 17 inches minimum....
-
Fixed or Built-in Seating and Tables [4.32]
[See subsections ...]