Side Approach The maximum reach depth for a high (54 inch maximum) reach is 10 inches, measured from the clear floor space....
Search Results "Mitigating Measures"
-
Side Approach
-
1013.4 Height
Tent platforms shall be 19 inches (485 mm) high maximum measured from the clear ground space to the tent platform surface....
-
1.2.4
1.2.4 When local horizontal discontinuities and vertical alignments are measured according to Section 1.1.9 a recommended tolerance is ±1/8 in. (3 mm)....
-
11B-1009.4.2 Height
The height of the transfer wall shall be 16 inches (406 mm) minimum and 19 inches (483 mm) maximum measured from the deck....
-
11B-1009.4.2 Height
The height of the transfer wall shall be 16 inches (406 mm) minimum and 19 inches (483 mm) maximum measured from the deck....
-
407.4.8.2.2 Signal Level
The verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the annunciator....
-
1009.4.2 Height
The height of the transfer wall shall be 16 inches (405 mm) minimum and 19 inches (485 mm) maximum measured from the deck....
-
I. Slip Resistant Surface—Aisles, Steps, Floor Areas Where People Walk, Floor Areas in Securement Locations, Lift Platforms, Ramps
While the dynamic coefficient of friction during walking varies in a complex and non-uniform way, the static coefficient of friction, which can be measured in several ways, provides a close...
-
Doorbell Factory Round Stainless Steel Doorbell
Solid 3/16" thick Stainless Steel Plate Comes with non-lighted stainless steel push button and mounting screws Measures 2 3/4" round Usually ships in 1-3 business...
-
5.1.2 Transfer Surface High Height
The transfer surface should have an adjustable height range with an upper height measuring at least 25 inches....
-
Technical Requirements
Technical Requirements—Specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
4.34.5.2(2)
(2) The height of the water closet shall be at least 15 in (380 mm), and no more than 19 in (485 mm), measured to the top of the toilet seat....
-
§ 37.155(a)(1)
(1) Effects on current fixed route service, including reallocation of accessible fixed route vehicles and potential reduction in service, measured by service miles;...
-
Can parking signage height be considered a "safe harbor"?
A height of at least 60 inches (measured to the bottom edge) is generally advisable (taking care not to make the sign a protruding object), although a higher height is better for signs at...
-
2.3.3 Comparison of Dimensions with Standards and other Anthropometric Studies
Measurements were taken manually using conventional measuring tools including a tape measure, steel square and spirit level....
-
Seating Locations
Remember, when measuring the accessible route through the space, measure the aisle width as if the chairs are pulled out and occupied....
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
13 [§ 4.7.10]
When taking this measurement, the measuring tape should be aligned parallel to the ramp run itself and should stretch from the intersection of the ramp and gutter to the innermost edge of...
-
M304.2.1 Slip Resistant (Section-by-Section Analysis)
One manufacturer commented on this requirement, requesting that the rule provide clarification on how to define or measure a standing surface as “slip resistant.”...
-
1012.2 Height
Guards shall form a protective barrier not less than 42 inches (1067 mm) high, measured vertically above the leading edge of the tread, adjacent walking surface or adjacent seatboard....
-
E102.8 TIA (Section-by-Section Analysis)
TIA 1083 (2007), Telephone Terminal Equipment Handset Magnetic Measurement Procedures and Performance Requirements, would be incorporated by reference at 410.4.2....
-
C102.3 American National Standards Institute/ Institute of Electrical and Electronics Engineers (ANSI/IEEE)
ANSI/IEEE C63.19-2011 American National Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids, Committee C63 – Electromagnetic Compatibility...
-
10.2.1(1)
new bus stop pads are constructed at bus stops, bays or other areas where a lift or ramp is to be deployed, they shall have a firm, stable surface; a minimum clear length of 96 inches (measured...
-
E102.3 American National Standards Institute/ Institute of Electrical and Electronics Engineers (ANSI/IEEE)
ANSI/IEEE C63.19-2011 American National Standard for Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids, Committee C63 – Electromagnetic Compatibility...
