(d) A housing facility or community may allow occupancy by families with children as long as it meets the requirements of §§100.305 and 100.306(a)....
Search Results "Children's Dimension"
-
§100.306(d)
-
Conventional Strollers
Strollers for one or two children are common, but strollers that carry three or four children are available as well....
-
M305.2.4 Cross Section (Section-by-Section Analysis)
of 2 inches maximum, and a perimeter dimension of 4 inches minimum and 4.8 inches maximum....
-
Amusement Rides: ADA Standard Section 216.12
Section 216.12 covers scoping requirements in the current ADA Standards for signs at amusement rides.
-
5.4.6 Transfer Support Gripping Surface Cross Section and Clearances for M301, M302, and M305.2
Grab bars with non-circular cross sections must have a cross section dimension of 2 inches maximum and a perimeter dimension of 4 inches minimum and 4.8 inches maximum....
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
§ 36.311(b)(2)(i)
(i) The type, size, weight, dimensions, and speed of the device;...
-
§ 35.137(b)(2)(i)
(i) The type, size, weight, dimensions, and speed of the device;...
-
Transfer Surface Size: Equipment Used by Patients in Supine, Prone, or Side-Lying Position (M301.2.2)
The transfer surface dimensions do not include headrests, footrests, or similar supports for body extremities that do not support the patient’s overall body position....
-
Knee & Toe Space [M303.2.4]
Rationale The issue of Clearance and Unobstructed Floor Space The knee and toe clearance dimensions, as well as the unobstructed floor space dimensions, dictate how close a patient...
-
407.4.6.2.1 Size
Buttons shall be ¾ inch (19 mm) minimum in their smallest dimension....
-
4.3.3 Clear Floor Area
The 95th percentile dimension values for occupied length and breadth provide a reasonable threshold value for determining the dimensions for clear floor area length and breadth....
-
608.2.2 Standard Roll-In Type Shower Compartments
Standard roll-in type shower compartments shall be 30 inches (760 mm) wide minimum by 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
Section 4.26.2
Handrail gripping surfaces with a non-circular cross section must have a perimeter dimension of 4 inches to 6 ¼ inches, and a cross section dimension of 2 ¼ inches maximum....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
R103 Conventions (Section-by-Section Analysis)
R103 Conventions (Section-by-Section Analysis) Conventional industry tolerances apply where dimensions are not stated as a range....
-
Role of HHS and DOJ
Role of HHS and DOJ The Children’s Bureau in the HHS Administration for Children and Families administers funding for child welfare agencies and courts and provides guidance and technical...
-
Transfer Systems: ADA Standard Section 1008.3
Moving between a transfer platform and a series of transfer steps requires extensive exertion for some children....
-
11B-409.4.6.1 Size
Control buttons shall be ¾ inch (19.1 mm) minimum in their smallest dimension....
-
§ 36.311(c)(1)
(1) The dimensions, weight, and operating speed of the mobility device in relation to a wheelchair;...
-
§ 35.137(c)(1)
(1) The dimensions, weight, and operating speed of the mobility device in relation to a wheelchair;...
-
3.2 Dimensional Tolerances
All dimensions are subject to conventional building industry tolerances for field conditions....
-
3.2 DIMENSIONAL TOLERANCES
All dimensions are subject to conventional building industry tolerances for field conditions....