M303.2.2 Width. Wheelchair spaces shall be 36 inches wide minimum. M303.2.3 Depth....
Search Results "Access Aisle Width"
-
5.8.1 Wheelchair Spaces on Raised Platforms Recommendations
-
4. On-board wheelchairs
On-board wheelchairs The existing rule requires that, on aircraft with more than 60 seats, the carrier must provide an onboard wheelchair in any case if the aircraft has an accessible...
-
Edge Protection
ADAAG addresses drop-offs along ramps and ramp landings but not along other portions of accessible routes or circulation paths....
-
Whitehall Mfg. WH2105BAR Bariatric Toilet Siphon Jet Type Off-Floor
Product Details Material: Stainless Steel Brand: Dura-Ware Fixture Width: 14" Off-Floor/Wall Waste: Available as Option Top Supply: Available...
-
B.2.i. - What must an agency do to ensure its' acquisitions of EIT provide "comparable access"?
Unless an exception applies, an agency’s obligation to provide comparable access under Section 508 is satisfied by acquiring EIT that meets the applicable technical provisions in Subparts...
-
H.4.i. - Does presentation equipment procured have to meet the Access Board standards?
Presentation equipment, such as LCD data projectors and laptop computers, are considered EIT and therefore covered by the Access Board's standards, unless an exception applies....
-
SETTLEMENT AGREEMENT BETWEEN THE UNITED STATES OF AMERICA AND THE CITY OF CHESAPEAKE REGARDING THE ACCESSIBILITY OF POLLING PLACES
SETTLEMENT AGREEMENT BETWEEN THE UNITED STATES OF AMERICA AND THE CITY OF CHESAPEAKE REGARDING THE ACCESSIBILITY OF POLLING PLACES This settlement agreement (the "Agreement") is entered...
-
1012.1 General
The technical requirements address the width of parking spaces and pull-up spaces for recreational vehicles (1012.2); the width of parking spaces for vehicles, other than recreational vehicles...
-
§ 36.308(b) New construction and alterations
The provision and location of wheelchair seating spaces and companion seats and designated aisle seats in newly constructed or altered assembly areas shall be governed by the standards for...
-
Section 36.302 Modifications in Policies, Practices, or Procedures (Preamble, Section-by-Section Analysis)
That paragraph provides that a store with check-out aisles must ensure that an adequate number of accessible check-out aisles is kept open during store hours, or must otherwise modify its...
-
Section 36.302 Modifications in Policies, Practices, or Procedures (Section-By-Section Analysis and Response to Comments)
That paragraph provides that a store with check-out aisles must ensure that an adequate number of accessible check-out aisles is kept open during store hours, or must otherwise modify its...
-
11B-235.2 Boat slips
TABLE 11B-235.2 BOAT SLIPS TOTAL NUMBER OF BOAT SLIPS PROVIDED IN FACILITY MINIMUM NUMBER OF REQUIRED ACCESSIBLE BOAT SLIPS...
-
11B-235.2 Boat slips
TABLE 11B-235.2 BOAT SLIPS TOTAL NUMBER OF BOAT SLIPS PROVIDED IN FACILITY MINIMUM NUMBER OF REQUIRED ACCESSIBLE BOAT SLIPS...
-
36 CFR Parts 1190 and 1191 ADA and ABA Accessibility Guidelines - Preamble (Discussion of Comments and Changes)
Guidelines for Buildings and Facilities; Architectural Barriers Act (ABA) Accessibility Guidelines Preamble (Discussion of Comments and Changes) __________________________________...
-
11B-603.2.3 Door swing
Doors to accessible water closet compartments shall be permitted to encroach into the turning space without limitation....
-
11B-603.2.3 Door swing
Doors to accessible water closet compartments shall be permitted to encroach into the turning space without limitation....
-
Table of Contents
Routes 207 Accessible Means of Egress 208 Parking Spaces 209 Passenger Loading Zone and Bus Stops 210 Stairways 211 Drinking Fountains 212 Kitchens, Kitchenettes, and...
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
11B-703.2.7 Character spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
11B-703.2.7 Character spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
11B-809.8.3 Door maneuvering clearance.
The width of the maneuvering clearance shall extend 18 inches (457 mm) beyond the strike edge at the pull side of the door....
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
