Ride seats designed for transfer should involve only one transfer....
Search Results "Side Transfer Surface"
Filters
Commonly Searched Documents
-
1002.5 Amusement Ride Seats Designed for Transfer
-
Floor Surfaces: ADA Standard Section 408.4.2
Section 408.4.2 covers the current ADA Standards for the floor surfaces of limited-use/limited-application elevators.
-
Exposed Pipes and Surfaces: ADA Standard Section 606.5
Section 606.5 covers the current ADA Standards for exposed pipes and surfaces under lavatories and sinks.
-
g-iii
Is there clear maneuvering floor space in front of each accessible door (see ADA Standards § Fig. 25) and, on the pull side, is there at least 18 inches clear floor space beyond the latch...
-
11B-802.1.1 Floor or ground surface
The floor or ground surface of wheelchair spaces shall comply with Section 11B-302. Changes in level are not permitted. Exception: Slopes not steeper than 1:48 shall be permitted....
-
11B-802.1.1 Floor or ground surface
The floor or ground surface of wheelchair spaces shall comply with Section 11B-302. Changes in level are not permitted. Exception: Slopes not steeper than 1:48 shall be permitted....
-
604.5.1 Side Wall
The side wall grab bar shall be 42 inches (1065 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1370 mm) minimum from the rear wall. ...
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
Suggested accessibility guidelines for exterior concrete surfaces
The following tolerances may be applicable for exterior accessible surfaces....
-
403 Walking Surfaces
403 Walking Surfaces...
-
3.1.2 Surface of Vehicle Parking Spurs
The surface of vehicle parking spurs shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
5.3.2.2 Surface
The surface of the turning space and clear floor or ground space shall be firm and stable. ...
-
304.2 Floor or Ground Surfaces
304.2 Floor or Ground Surfaces. Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted....
-
407.12.2.2 Obstructed Side Reach (Section-by-Section Analysis)
407.12.2.2 Obstructed Side Reach (Section-by-Section Analysis) This section proposes that, where the operable part is located more than 10 inches, but not more than 24 inches, behind...
-
4.7.4 Surface
The surface of the clear floor or ground spaces required by section 4.0 shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
4.8.6 Cross Slope and Surfaces
The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....
-
4.8.6 CROSS SLOPE AND SURFACES
The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....
-
4.5.4 Surface
The surface of the clear floor or ground space for trash, recycling, and other essential containers shall be firm and stable....
-
304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted....
-
7.4.1 Surface
The trail tread surface, including resting intervals and passing spaces, shall be both firm and stable....
-
Figure 1009.5.1 Size of Transfer Platform – Drawing from the U.S. Access Board
-
4.3.4 Tent Pad or Platform Surface
Tent pads and platforms shall have a surface that is firm and stable and is designed to allow use of tent stakes and other tent securing devices. Exception. ...
